Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Monessen Hearth, modell ODGR400

Hersteller: Monessen Hearth
Dateigröße: 1.38 mb
Dateiname: c5f8374f-5ff1-4140-bd0d-e758f23cd2b1.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Fireplace Dimensions 36" (914mm) 40" (1016mm) 39......" (1007mm) ......" (16mm) ......" (13mm) ......" .........." (822mm) ...." (622mm) 43......" (1111mm) 8......" (210mm) ........" (165mm) ........" (191mm) Gas Line AccessRough Opening Height ......" (16mm) 22" (559mm) .........." (572mm) ...." (559mm) RecessedNailingFlangeRough Opening Width 41" Rough Opening Depth3......" (95mm) (1041mm) 3......" (98mm) 7114ODUVSR36ASpecs11/0368......" (1740mm) 48......" (1232mm) 48......" (1232mm) 14......" (362mm) 3......" (95mm) Low VoltageWire Access14......" (362mm) Low Voltage WireAccess Fig. 1 ODGR400 specification and framing dimensions. Fireplace Dimensions 42" (1067mm) 46" (1168mm) 39......" (1007mm) ......" (16mm) 50" (1270mm) 50" (1270mm) ......" (13mm) ......".......... " (1791mm) ...." (610mm) 43......" (1111mm) ........" (191mm) ........" (165mm) ........" (191mm) Rough Opening Height ......" (16mm) 22" (559mm) .........." (572mm) .........." (667mm) RecessedNailingFlangeRough Opening Width 47" Rough Opening Depth3" (76mm) 35......" (895mm) (1194mm) 7114ODUVSR42Aspecs11/0314......" (362mm) 3......" (95mm) Low VoltageWire AccessGas Line Access14......" (362mm) Low Voltage WireAccess Fig. 2 ODGR500 specification and framing dimensions. Moisture Resistance This outdoor fireplace will shed moderate amounts of water, but is not waterproof. Water and condensing water vapor may enter the chase under certain conditions. The fireplace will not perform as an exterior wall. Moisture penetration must be considered for construction that places the fireplace in structure walls or on moisture sensitive surfaces. When installed on exterior walls: MHSC recommends the fireplace chase be constructed outside the structure's weather envelope. Where the platform meets the wall, use a flashing detail similar to that required for attached decks. Chase platforms, including hearths should slope away from the structure at 1/4 in per foot. The fireplace can be shimmed level. When installed on surfaces where water may collect or cause damage: MHSC recommends a slope of 1/8 in to 1/4 in per foot towards the drain port suggested. The fireplace can be shimmed level. Hearths should slope away from the front of the fireplace and chase at 1/8 in to 1/4 in per foot. Metal safety strips must be on top of any combustible hearth materials used for moisture management. Mantels WARNING: A 4" hood must be used if a mantel is to be installed. The height that a combustible mantel is fitted above the fireplace is dependent on the depth of the mantel. This also applies to the distance between the mantel leg (if fitted) and the fireplace. For the correct mounting height and widths refer to Figures 3a and 3b Noncombustible mantels and legs may be installed at any height and width around the appliance. When using paint or lacquer to finish the mantel, such paint or lacquer must be heat resistant to prevent discoloration. ABYZFireplaceCFM146DV Mantel Chart7/5/01 sta Side View Standoff Maintain minimum 3/4" (19 mm) clearance to combustible. Screened Porch Installation The ODGR may be installed safely and is design certified by CSA to be installed in a screened porch with these guidelines: Minimum porch area...............................96 sq. feet (9 sq m) Minimum celing height......................................92" (234 cm) Minimum of two (2) walls must be screened Minimum top of screen height, side walls.........6'6" (198 cm) Minimum screen area.............................64 sq. feet (6 sq m) Top of Combustion Chamber CFM146 Ref. Mantel Ref. Mantel From Top Shelf Depth of Comb. Chamber Y 8" (203 mm) A 28" (711 mm) Z 1..." (38 mm) B 26" (660 mm) Clearance to Combustibles Fig. 3a Mantel clearances. Appliances Top...........................................................0” (0 mm) Bottom......................................................0” (0 mm) Side..........................................................0” (0 mm) Back.........................................................0” (0 mm) Perpendicular Sidewall............................0” (0 mm) Top of unit to ceiling...........................36” (914 mm) Front of unit to combustibles..............36” (914 mm) Hearth A hearth is not mandatory but is recommended for aesthetic purposes. We recommend a noncombustible hearth. JFGHIMantelLegCFM164aMantel Leg Chart06/22/01 sta Framing and Finishing Check appliance to make sure it is levelled and properly positioned. The appliance should only be mounted on the following surfaces: • A flat combustible (burnable) surface. • A raised wooden platform. • A concrete block or other solid object placed beneath each of the four corners of the appliance. To mount the appliance: 1. Choose unit location. 2. Four (4) nailing flanges are supplied with the fireplace (found on the fireplace hearth). To level the box and secure it firmly in place, remove the nailing flanges from the hearth and install at the sides of the fireplace as shown in Figure 4. Black Surround Face...