Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Aga Ranges
Dateigröße: 973.12 kb
Dateiname: 796077aa-1b5b-4014-adbc-5815aff5568d.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
If using a drain pump, check the inlet screen, discharge line, and vent line for any build or restrictions. Leaking drain valve. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit. This will also dissolve and flush out foreign material in the drain valve causing it to leak. Room temperature is too warm. Move to an area where temperature is below 90 deg. F. Ice cubes are too big (greater than 3/4 inch Ice slab not releasing. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for thick). proper operation and cube size. Condenser fan air flow is restricted. Make certain the grille in the front of the unit is free and open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the unit. Clean the condenser with a vacuum and brush attachment. Room temperature is too warm. Move to an area where temperature is below 90 deg. F. Hollow ice slab. Distributor tube is restricted. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation. Build up of deposits on evaporator plate. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation and cube size. Low water level in reservoir. Make sure that the reservoir drain plug is installed properly. Check the water line to the unit to make sure there are no restrictions or kinks in the line. Check all filters to make sure they are not restricted or plugged. All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Trouble Shooting Three Problem Possible Cause Correction Ice is not clear. Low water level in reservoir. Make sure that the reservoir drain plug is installed properly. Check the water line to the unit to make sure there are no restrictions or kinks in the line. Check all filters to make sure they are not restricted or plugged. Softened water supply. Make certain that water line is not connected to the water softener. Room temperature is too cold. Move the unit to an area where room temperature is above 55 deg. F. Low ice production. Unit is running, has Low water level in reservoir. Make sure that the reservoir drain plug is installed properly. run over a 48 hour period, and there is lit-Distributor tube is restricted. Check the water line to the unit to make sure there are no restrictions tle ice in bin. or kinks in the line. Check all filters to make sure they are not restricted or plugged. Build up of deposits on evaporator plate. See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation. Inadequate drain system. Restriction in drain lines will cause ice in the bin to melt. If using a gravity drain, make certain there are no kinks or restrictions in the drain lines. If using a drain pump, check the inlet screen, discharge line, and vent line for any build or restrictions. Condenser fan air flow is restricted. Make certain the grille in the front of the unit is free and open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the unit. Clean the condenser with a vacuum and brush attachment. Unit continues to run and produce ice. Ice bin is not full. The unit will automatically shut down when ice reaches the sensing tube. Ice bin is full. The unit will automatically shut down when ice reaches the sensing tube and has completed the harvest of the ice slab. Room temperature is too warm. Move the unit to an area where room temperature is below 90 deg. F. Ice machine is not level. Use a level to check the unit for level from side to side and front to rear. Grid-cutter is not cutting the ice slab. The selector switch is not in the "ON" position Set the rocker switch on the grille of the ice machine to the "ON" position. The grid cutter is not plugged into the receptacle. Remove the escutcheon panel and plug the grid-cutter into the receptacle on the side of the line. Time to cut through the slab. It can take up to 35 minutes to cut through a harvested ice slab. This is normal operation. All specifications and product design subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Troubleshooting Four Problem Possible Cause Correction Ice cubes are sticking together. Ice consumption is low. Room temperature is too warm. Use the ice in the bin frequently. Ice will stick together if left in insulated bin over long periods of time. Move the unit to an area where temperature is below 90 deg. F. Ice level is too high. The ice machine is not level. Room temperature is too warm. Ice deflector is not in place or secured properly. Bin level sensing tube needs adjusted. Use a level to check the unit for level from side to side and front to rear. Move the unit to an area where temperature is below...