Stimmen - 5, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
70—latest edition in the United States, or CSA C22.1, Part 1 in Canada, and local code requirements. Tools You Will Need Phillips® Screwdriver Pencil Ruler or Tape Measure and Straight-edge Hand Saw or Saber Saw Spirit Level Warm & Serve Drawer Installation 1.Locate the 2 anti-tip brackets supplied as shown on fig. 1. 2.Slide drawer into cutout opening until front frame of drawer is flush against cabinet. Be careful not to pinch electrical cord. 3.Remove the drawer as instructed in the Use & Care Guide and secure drawer housing to cabinet using the 3 nickel-plated screws supplied (see Figure 2). Do not overtighten screws. 4.The 60" (152,4 cm) appliance power cord can now be connected into the 120 Volt outlet. 5.Proceed with mounting built-in oven above the drawer (if applicable). Follow installation instructions provided with built-in oven. Make sure to use anti-tip brackets supplied with the built-in oven. Figure 2 supplied to attach drawer to front of Use screws cabinet. c/c 25 5/16" (64,3 cm) 24" (61 cm) Max. 23 5/8" (60 cm) Min. c/c 12 21/32" (32,15 cm) Figure 1 2 WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS 30" WARMER DRAWER FRONT PANEL INSTALLATION INSTRUCTIONS WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS 30" WARMER DRAWER FRONT PANEL INSTALLATION INSTRUCTIONS Front Panel Installation instructions: First, install the drawer handle (if applicable) on the wood panel. 1. Remove the 5 screws located at position A which are fixing the drawer mounting panel to the drawer interior panel. 2. Place the drawer mounting panel on the inside of the drawer wood panel as per figure 2. Fix the drawer wood panel (supplied by the customer) to the drawer mounting panel using the 4 wood screws supplied at location B. 3. Reinstall this new assembly wood & mounting drawer panel to the drawer interior panel. BBAAAAADrawer Interior Panel Drawer Mounting Panel Drawer Wood Panel (supplied by the customer) Figure 1 Drawer Wood Panel (supplied by the customer) 11.’’ 30’’ Center lineDrawer Mounting Panel Note: Wood panel should be .’’ min. thick. Figure 2 3 WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS Electrical connection IMPORTANT Please read carefully. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong grounding wall receptacle to minimize the possibility of electric shock hazard from the appliance. The wall receptacle and circuit should be checked by a qualified electrician to make sure the receptacle is properly grounded. Where a standard 2-prong wall receptacle is installed, it is the personal responsibility and obligation of the consumer to have it replaced by a properly grounded 3-prong wall receptacle. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Disconnect electrical supply cord from wall receptacle before servicing cooktop. Preferred Method Grounding type wall receptacle Power supply cord with 3-prong grounding plug. Do not, under any circumstances, cut, remove, or bypass the grounding prong. Model and Serial Number Location The serial plate is located as shown below. When ordering parts for or making inquiries about your Warm & Serve Drawer, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your Warm & Serve Drawer. Plate Location Serial Combination Warm & Serve Drawer and Cooktop Installation Cooktop Cutout Warmer Drawer Cutout You can install the warmer drawer in combination with an electric or gas cooktop. You must follow the specifications from the installation instructions of the cooktop to avoid interference with the gas or electric installation. 4 WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS LA INSTALACIoN Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. PARA SU SEGURIDAD: No almacene ni utilice gasolina u otros vapores y liquidos inflamables en la proximidad de este o de cualquier otro artefacto. Canada Estados Unidos INFORMACIoN GENERAL: El cajon calentador puede ser IMPORTANTE: El cajon calentador debe de estar instalado usado como unidad independiente o en una combinacion entre con una superficie llana, de la izquierda a la derecha, de la el cajon calentador y el horno integrado y montado por encima del parte de atras al frente. La superficie debe poder sostener cajon. 100 libras (45,4 Kg). Dimensiones del cajon calentador Instalacion de la unidad independiente Instalacion de la combinacion cajon calentador y horno de integrado NOTA: Un cable de 60" (152,4 cm) de largo es suministrado con el cajon calentador. IMPORTANTE: El cajon calentador funciona con un suministro de energia electrica de corriente alterna, de tres cables, de una sola fase, de 120 voltios, 60 hertz con linea ...