Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Haier, modell HPIM25SS

Hersteller: Haier
Dateigröße: 868.79 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

If the unit doesn't stop, even with ice cubes obstructing the sensor, move the unit out of the sunlight. 6. To continue making ice, check that there is water in the water storage tank. If there is no water in the water storage tank, then no water will be pumped into the water box, and the operation will stop. The "Add Water" LED display will light up. Press the “OFF” button. Fill the water storage tank with water, and then press the “ON” button for the icemaker to begin operating again. Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting. 7. If the compressor stops for any reason such as water shortage, too much ice, power off, etc., do not restart the machine right away. Wait at least 3 minutes before restarting the machine. English ClEANING AND MAINTENANCE Before using your icemaker, it is strongly recommended that you clean the icemaker thoroughly. Be sure to clean the icemaker regularly. 1. When cleaning, please make sure the power has been turned off and the plug is disconnected from the outlet. When plugging or unplugging the unit from the outlet, pull directly on the plug. Never pull on the power cord. 2. Remove the ice storage basket. 3. Drain remaining water from the unit by unplugging the drain plug on the front bottom side. When cleaning is completed, the plug must be properly inserted back onto the drain otherwise the icemaker will leak. 4. Use a mild detergent diluted in warm water and wipe with a soft towel or sponge. Solvents, detergents and abrasives must never be used for cleaning. 5. Wipe the inner parts, such as the ice storage basket, water reservoir, water box, ice pusher, and evaporator rods. 6. The outside of the icemaker should be cleaned regularly with a mild detergent solution, warm water, and a soft cloth. 7. Dry the interior and exterior with a soft cloth. 8. To begin making ice once the unit has been cleaned, pour clean water into the water reservoir and fill up to the level line follow operating instructions. Never tilt or place the icemaker on its side, otherwise you must wait 10 hours for compressor coolant to settle. 9. To ensure the cleanliness of the ice cubes, the water in the water storage tank should be replaced every 24 hours. 10. When the machine is not in use or will not be used for an extended period of time, pull out the drain plug at front bottom of the machine to empty the remaining water in the water reservior completely. (Follow the instructions in number 4 above.) Drain Cap Rubber Plug Drain Spout 10 English TROUblESHOOTING GUIDE Problem Possible Causes Solution “ADD WATER” indicator light turns on. Low water level or lack of water. Add water and the icemaker will operate automatically. There is no indication on the control panel. Disconnection of plug. Check that the plug is plugged into the electrical outlet. “Ice Full” and “Add Water” indicators light up simultaneously. Electrical Power Surge or There may be air in the lines or the lines are blocked. The water Turn off the icemaker, pull out the electric plug, fill it with water if needed, replace the plug and then restart the unit. or Check if ice is blocking the ice pusher. Turn off the unit; let the tank cannot detect water level. ice melt and restart. Otherwise, call Haier America Customer Service. The “Ice Full” indicator light is on. The ice basket is full or the ice basket is not full or no Remove ice from the ice storage basket to make more or hold down the "Select" button for 5 seconds, the ice maker ice in the basket. will make ice for 10 cycles even though the "Ice Full" indicator is lit. The unit does not operate. Power is not being supplied to the unit. The ambient temperature or the water temperature is too high. Plug the unit into a standard 110/120 Volt, 60 Hertz power source. Please run the icemaker in temperatures below 90°F and/or pour colder water into the water reservoir. Ice blockage. No ice is being made. Making ice takes too much time. Turn off the machine. Start the machine after the ice block melts. Or change the size selector to small ice cubes. The icemaking cycle seems normal but no ice is produced. There is refrigerant leakage. A pipe in the cooling system is blocked. Consult a qualified technician or call Haier America Customer Service. Note: There is protective circuitry inside this icemaker to protect the circuitry from overheating and the icemaker will automatically shut down to prevent damage if activated. Please disconnect power cord and restart after 30 minutes of cooling down time. For Haier America Customer Service, please call: 1-877-337-3639 11 English lIMITED WARRANTy What is covered and for how long? This warranty covers all defects in workmanship or materials for a period of: 12 months for labor 12 months for parts (Functional Parts Only) The warranty commences on the date of item purchase. Customer shall provide Haier with proof of the date of purchase and the original receipt along with: brand, model and serial number for v...