Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung GE, modell GFC1000F

Hersteller: GE
Dateigröße: 603.54 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Run your fingers Bottom around the entire Bead cushion mount with slight pressure. Do not press too hard. When the cushion mount is properly seated, the mount ring can be pulled downward over the cushion mount and will be free to turn. Installation Instructions DISHWASHER CONNECTION (IF REQUIRED) If you are connecting to a dishwasher, complete the following step. If a dishwasher is not to be connected, go on to “Attaching the Discharge Elbow” section. KNOCK OUT PLUG Using a blunt instrument (steel punch or wooden dowel), knock out entire plug. Do not use a screwdriver or sharp instrument. When knockout plug falls into disposer, you may remove it or simply grind it up when the disposer is used. This will not damage the disposer in any way, but may take some time to grind, over the course of several uses. 1 Connect the dishwasher hose using a hose clamp. If the hose size is different, you will need a stepped rubber adapter. CONNECT HOSE2 Knock out plug Hose Clamp Stepped Rubber Adapter CONNECT DISCHARGE ELBOW Connect the discharge elbow to the disposer.* Make sure all plumbing connections are tight. ATTACHING THE DISCHARGE ELBOW 3 Rubber Gasket Discharge Elbow * Some installations (see page 8 for examples) may require the use of a flexible drain pipe. Installation Instructions 4 CONNECTING DISPOSER TO SINK FLANGE LOCK MOUNT RING Turn the mount ring to the right until it locks up tight. Hopper projections must be to the extreme left of the mounting slots. If the mount ring is hard to turn, you may add a small amount of petroleum jelly or liquid soap to the hopper projection. Run water and check for leaks. 3 Hopper Projection in “Supported” Position Hopper Projection in “Locked” Position Mount Ring Locking Detail Check the unit for leaks 24 hours after installation and first operation. CHECK FOR LEAKS4 Line up the disposer under the sink flange. Guide the hopper projections into the mount ring slots. Turn the mount ring about 1/4. to the right so that the disposer is temporarily supported. 1 Turn the mount ring and the disposer until the disposer discharge elbow lines up with the outlet pipe (see page 8). LINE UP WITH OUTLET PIPE2 Mount Ring Slot Hopper Projection Discharge Elbow Outlet Pipe ATTACH TO SINK FLANGE Installation Instructions DIMENSIONS GFC320F GFC325F 63/16” 5 3/16” 1211/16” 41/2” 11/2” 53/8” GFC520F GFC525F GFC530F GFC535F GFC720F GFC1020F 11/2” 11/2” 11/2” 59/16” 7 1/4” 8 1/2” 161/16” 71/4” 8 1/2” 5 9/16” 141/2” 615/16” 53/8” 73/4” 137/16” 4 1/2” 4 1/2” 4 1/2” GFB760F Batch Feed Operation 11/2” 93/8” 8 1/2” 5 9/16” 165/8” 41/2” 11/2” 59/16” 93/8” 8 1/2” 183/16” 4 1/2” GFB1060F Batch Feed Operation 63/16” 5 3/16” 1211/16” 41/2” 11/2” 53/8” SOME TYPICAL INSTALLATIONS SINGLE BOWL DOUBLE BOWL CENTER OUTLET** DOUBLE BOWL END OUTLET** *Approx. *Approx. *Approx. Direct replacement for most makes & models. *9. for model GFC320F, GFC520F, GFC325F, & GFC525F. *10. for models GFC530F, GFC535F, GFC720F & GFC1020F. *12. for models GFB760F & GFB1060F. **Flexible drain pipe may be necessary for this application. NOTE: It is essential for the proper operation of the disposer that this dimension be 9. –12. , depending upon the models listed above, to avoid standing water in disposer motor housing. Operating instructions. This disposer uses anti-jam swivel impellers that make a clicking sound as they swing into place. This indicates normal operation. Continuous Feed Models Consumer SupportTroubleshooting TipsInstallation InstructionsSafety Instructions Operating Instructions A. Remove the sink stopper and turn on a medium flow of cold water. B. Turn the switch to ON. C. Scrape in food waste. To speed up food waste disposal, cut or break up large bones, rinds and cobs. Large bones and fibrous husks require considerable grinding time and are more easily thrown away with other trash. Do not be alarmed that the disposer slows down while grinding. The disposer is actually increasing torque (grinding power) and is operating under normal conditions. Batch Feed Models D. Before turning the disposer off, let the water and the disposer run for approximately 25 seconds after shredding stops. This assures that all waste is thoroughly flushed through the trap and drain. E. Do not use hot water while running the disposer. Cold water will keep food waste and fats solid so they can be flushed down the drain. Oval Handle Small A. Remove the sink stopper and turn on a medium flow of cold water. B. Scrape in food waste. C. Insert the stopper to start the disposer. One of the two small slots in the stopper base must line up with the switch plunger inside the neck of the disposer. NOTE: The oval shaped handle aligns with the 2 small slots in the stopper. Push down firmly to start. D. Run the disposer for 25 seconds after shredding stops. This assures that all waste is thoroughly flushed through the trap and drain. Lift the stopper to shut the disposer off. E. To fill the sink, insert the stopper so that the large...