Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Check the type of your machine before reading this manual. (For details, see page 2.) Type 1 = 9450 Type 2 = 9550 Certain types may not be available in some countries. For details, please contact _your local dealer._ Note: Certain options may not be available in some countries. For details, please _contact your local dealer._ Savin shall not be responsible for any damage or expense that may result from the use of parts other than genuine Savin parts in your Savin office product. _ For good copy quality, Savin recommends that you use genuine Savin toner. Power Source: 120V, 60 Hz, more than 20A Please make sure to connect the power cord to a power source as above. For details about power cord, see page iv._ SAFETY INFORMATION SAFETY INFORMATION When using your copier, the following safety precautions should always be followed. Safety During Operation In this manual, all safety messages are identified by the words "WARNING" and "Caution". These words mean the following: WARNING: Important information to alert you to a situation that might cause serious injury and damage to your property if instructions are not followed. Caution: Important information that tells how to prevent damage to equipment, or how to avoid a situation that might cause minor injury. WARNING: □ Since some parts of the copier are supplied with high electrical voltage, touch only the parts specified in this manual and the machine’s display. □ Do not modify or replace any parts other than the ones specified in this manual and the machine’s display. □ Do not incinerate toner or toner containers. Toner dust may ignite when exposed to open flame. □ Do not store toner where it will be exposed to heat. □ Do not eat or swallow toner, and keep it out of reach of children. □ The fusing unit may be very hot. Be careful when handling it. Caution: □ While copying, do not turn off the main switch. □ While copying, do not open the front doors. □ While copying, do not unplug the power cord. □ Do not lay anything weighing more than 10 kg (22 lb) on the exposure glass. □ Keep corrosive liquids, such as acid, off the machine. □ Do not allow paper clips, staples, or other small metallic objects to fail inside the machine. SAFETY INFORMATION General Safety Information □ Always turn the copier off when you have finished copying for the day, but leave it plugged in. □ When the copier will not be used for a long period, disconnect the power cord. □ If the copier must be transported by vehicle, please contact your service representative. □ When the main switch is in the Stand-by position, the anticondensation heaters are on. In case of emergency, unplug the machine’s power cord. □ The main plug on this equipment must be used to disconnect main power. Copier Environment INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Copier Environment The instailation location should be carefully chosen because environmental conditions greatly affect the performance of a copier. - Optimum environment conditions - □ Temperature: 10 - 30°C (50 - 86°F) □ Humidity: 15 - 90% □ A strong and level base. □ The copier must be level within 5 mm (0.2") both front to rear and left to right. □ To avoid possible build-up of ozone, make sure to locate this copier in a large well ventilated room which has air turnover of more than 30m3/hr/person. Environments To Avoid □ Locations exposed to direct sunlight or strong light (more than 1,500 lux). □ Locations directly exposed to cool air from an air conditioner or heated air from a heater.(Sudden temperature changes may cause condensation within the copier.) □ Places where the copier may be subjected to frequent strong vibration. □ Dusty areas. □ Areas with corrosive gases. □ Places higher than 2,000 m (6,500 ft) above sea level. INSTALLATION REQUIREMENTS Power Connection Power Connection □ Avoid multiwiring. □ Make sure that the wall outlet is near the copier and easily accessible. □ Make sure the plug is firmly inserted in the outlet. □ Voltage must not fluctuate more than 10%. □ Do not set anything on the power cord. Access To Copier □ Place the copier near the power source, providing clearance as shown: More than 10 cm (3.9") More than 10 cm (3.9") * Your machine More than 90 cm (35.4") More than 10 cm *1 (3.9") ' *1 If the optional 3,500-sheet large capacity tray is not installed, the distance between the wall and the edge of the bypass feed tray must be more than 30 cm. *2 If the compact sorter stapler is installed, the distance must be more than 20 cm. *3 See page 83. iv STORAGE OF SUPPLIES STORAGE OF SUPPLIES Storage Of Supplies Paper Storage Paper should always be stored properly. Improperly stored paper may result in poor image reproduction, creased copies, and paper misfeeds. □ Avoid storing paper in humid areas. (Under high temperature and high humidity conditions, store copy paper in a vinyl bag.) □ Do not store paper where it will be exposed to heat. ...
Dieses Handbuch ist für folgende Modelle:Drucker - 9550 (3.41 mb)