Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
For more detailed installation information, please refer to the user manual in the enclosed CD. The contents of the CD include the following. 1. Manual: User Manual, Code Chart, Control Commands 2. Drivers: Windows Drivers, OPOS Drivers 3. Utilities: a logo download tool and a virtual memory switch control tool . Components Ribbon Cartridge Paper Roll Procuct Installation CD CD SRP-275 AC/DC Adaptor Power Code Installation Guide . Connecting the cables 1. Turn off the printer and the host ECR (host computer). 2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector of the printer. 3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface connector cable accordingly. 4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer. . Installing the Ribbon Cartridge 1. Before inserting the ribbon cartridge, turn the knob clockwise to prevent twisting of the ribbon. 2. Open the front cover of the printer and remove the old ribbon cartridge, if any. 3. Insert the ribbon cartridge as shown in the figure so that the ribbon is aligned to the rear of the printer head. 4. To allow the ribbon to move freely within the cartridge when inserting the ribbon cartridge, turn the knob clockwise once more. 5. Close the front cover of the printer. . Note Malfunctions and other problems may arise if other than specified ribbon cartridges are used in the printer. The Warranty may be void if other than specified ribbon cartridges are used. For detailed information regarding the ribbon cartridge, refer to the product specifications. . Changing the Paper Width 1. Open the rear cover. 2. Remove the frame paper control by loosening the two screws (3x6). 3. Place the frame paper control in the desired position and tighten the two screws once again. (The default paper width is set at 76mm.) 4. Close the rear cover. 5. Change the Memory Switch Setting to complete changing the paper width. Refer to the memory switch setting information in the user's manual. . Installing the Paper Roll 1. Open the rear cover. 2. Insert a new paper roll, making sure to align it properly. 3. Pull out a small amount of paper, and close the cover. . Using the Operation Panel • FEED (Button) Press the FEED button once to discharge extra paper. Holding down the FEED button will discharge paper continuously until the button is released. • POWER (LED, GREEN) When turning on the power, a green LED will be lit. Do not use the printer or turn it off when this LED blinks) • ERROR (LED, RED) When an error occurs, a red LED will be lit. (e.g. no paper, cover ajar, etc.) • PAPER (LED, RED) The paper LED will be red when the paper roll is running low. If there is no paper left, the paper LED will be on together with ‘Error’ LED. . Setting the DIP Switches Changing Dip Switch settings must be done when the printer is off. Any changes done while the printer is on will not be processed. • DIP Switch 1 SW Function ON OFF Default 1-1 1-2 Emulation Refer to the following table 1 OFF 1-3 Auto Cutter Enable Disable OFF 1-4 Reserved - OFF 1-5 Serial Interface Memory Switch DIP Switch OFF 1-6 Printing NV bit image after cutting Enable Disable OFF 1-7 Near-End Sensor Status Enable Disable OFF 1-8 Printing Lines 42/35 40/33 OFF • DIP Switch 2 (RS232C Serial Interface Model) SW Function ON OFF Default 2-1 Data Receive Error Ignore Print “?” OFF 2-2 Reserved OFF 2-3 Handshaking XON/XOFF DTR/DSR OFF 2-4 Data Length 7 bits 8 bits OFF 2-5 Parity Check Enable Disable OFF 2-6 Parity Selection EVEN ODD OFF 2-7 OFF 2-8 Baud Rate Selection Refer to the following table 2 OFF • DIP Switch 2 (Parallel Interface Model) SW Function ON OFF Default 2-1 Auto Line Feed Enable Disable OFF 2-2~8 Undefined OFF (1) DIP Switch setting for Citizen (iDP 3550) Mode • DIP Switch 1 SW Function ON OFF Default 1-1 1-2 Emulation Refer to the following table 1 OFF 1-3 Auto Cutter Enable Disable OFF 1-4 CBM command CBM2 Mode (iDP3530 System) CBM1 Mode (iDP3540 System) OFF 1-5 1-6 1-7 International Character Refer to the following table 3 ON 1-8 CR Mode CR CR+LF OFF • DIP Switch 2 (RS232C Serial Interface Mode) SW Function ON OFF Default 2-1 Data Length 8bits 7bits ON 2-2 Parity Check Disable Enable ON 2-3 Parity Selection ODD EVEN ON 2-4 Handshaking DTR/DSR XON/XOFF ON 2-5 2-6 Baud Rate Selection Refer to the following table 2 OFF 2-7 Near-End Sensor Status Enable Disable OFF 2-8 Mechanism Type Graphic Text OFF (2) DIP Switch setting for Star (SP500) Mode • DIP Switch 1 SW Function ON OFF Default 1-1 1-2 Emulation Refer to the following table 1 OFF 1-3 Auto Cutter Enable Disable OFF 1-4 Printing in Black/Red Enable Disable OFF 1-5~8 Reserved OFF • DIP Switch 2 (RS232C serial interface model) SW Function ON OFF Default 2-1 2-2 Reserved OFF 2-3 Handshaking XON/XOFF DTR/DSR OFF 2-4 Data Length 7bits 8bits OFF 2-5 Parity Check Enable Disable OFF 2-6 Parity Selection EVEN ODD OFF 2-7 OFF 2-8 Baud Rate Selection Refer to the followin...
Dieses Handbuch ist für folgende Modelle:Drucker - SRP-275 (1.63 mb)