Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Cartridges are vacuum packed to maintain reliability. Remove all protective materials. 2 Turn on 1 Connect the power cable. Caution: Do not connect to your computer yet. 2 Press the On button. 3 Select language 1 To select English as your language, press Start. Note: If you want to change the language, press or to select it, then press Start. 4 Install ink cartridges Note: Do not load paper yet. 1 Lift up the scanner, then open the cartridge cover. 2 Shake the ink cartridges gently 4 or 5 times, then unpack them. 3 Remove only the yellow tape from each cartridge. Caution: Don’t remove any other seals or the cartridges may leak. *411841500* *411841500* Epson Stylus® NX420 Series 3 Squeeze the edge guide as you slide it all the way to the left. 4 Load letter or A4-size paper against the right edge and behind the tab, with the printable side face up. 5 Slide the edge guide over. Continue with section 6 to choose your connection type. 4 Insert the cartridges in the holder for each color. 5 Press each cartridge down until it clicks. 6 Close the cartridge cover. Press down until it clicks. 7 Lower the scanner. 8 Press the Start button to charge the ink. Priming takes about 2 minutes. Note: Your printer ships with full cartridges and part of the ink from the first cartridges is used for priming the printer. Caution: Don’t turn off the printer while it is priming or you’ll waste ink. 5 Load paper 1 Open the paper support and pull up the extensions. 2 Open the output tray, pull out the extensions, and raise the stopper. 3 Click Install and follow the on-screen instructions. Control panel overview Turn power on/off Copy document or photo Print photo from memory card Scan document or photo Check ink level and perform maintenance Select number of copies Reduce/enlarge copies Select paper size and type Start printing Cancel printing and clear settings LCD display screen Browse photos Any problems? If you experience problems during setup, see below: Network setup was unsuccessful. • Make sure you select the right network name. • If your network has security enabled, make sure you enter your network password (WEP key or WPA passphrase) correctly. If it has uppercase (ABC) or lowercase (abc) letters, make sure you enter them correctly. 6 Choose your connection You can connect your printer to your existing network wirelessly or directly to your computer using a USB cable (not included). See below for details on each connection method. Wireless Connection You will need to install the software on every computer that will print to the printer. Temporary use of a USB cable (not included) is recommended for the first installation only. After the printer is connected to the network, you will be prompted to remove the USB cable. If you’re using Mac OS® X 10.6 or don’t have a USB cable, you can use the buttons on the printer to select wireless settings instead. Make sure you know your network name (SSID) and network password: • Network name • Network password If you don’t have this information, contact the person who set up your network. Direct USB Connection Make sure you have a USB cable (not included). Do not connect the printer to your computer until you’re instructed to do so. 7 Install software 1 Make sure the printer is NOT CONNECTED to your computer. Windows®: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the NX420 Series software CD. Windows: If you see the AutoPlay window, click Run Setup.exe. If you see the User Account Control screen, click Yes or Continue. Macintosh®: Double-click the Epson icon, if necessary. s to select upper-case letters (ABC), lower-case letters (abc), or numbers and symbols (123). Press + or – to enter characters. Press to move to the next character. Press to delete. Press the Start button when you’re finished entering your password. • If you see a firewall alert message, click Unblock or Allow to let setup continue. You see error messages on the printer’s LCD display screen. See your Quick Guide for troubleshooting information. Setup is unable to find my printer after connecting it with a USB cable. Make sure it is securely connected as shown: Any questions? Quick Guide Basic instructions for wireless setup, printing, copying, and scanning. User’s Guide Click the desktop shortcut to access the online User’s Guide, how-to videos, software downloads, Epson Supplies CentralSM, and more (requires an internet connection). On-screen help with your software Select Help or ? when you’re using your software. Epson Technical Support Visit epson.com/support where you can download drivers, view manuals, get FAQs, or e-mail Epson. You may also speak with a support specialist by calling (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. Need paper and ink? Try Epson paper...