Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
1 kHz Effect on/off 1 M ohm 1К ohm Ш(%'phone) AC Power (Miniature Phone) Director Output (M* phone) Detoy/Mix Output (%* phone) 9 V DC Dry Сей Battery (NEDA 1604A/IEC: 6LR61 Peavey AC Adaptor. Part #70900666) Under normal extended playing time use. battery operation of this unit is not recommended. 80mffliamps(MA) Due to our efforts for constant improvements, features and specifications are subject to change without notice. NORMAL OPERATION EFFECTS LOOP OPERATION REGARDING EFFECTS LOOPS: Time-delay-based effects such as chouses, Hangers, and delays (echo) should be placed, when possible, in the amplifier's effects loop. SPECIAL PRECAUTIONS • When using the effects unit with an AC adaptor, use only a Peavey supplied +9 volt adaptor or equivalent. • When the unit is not in use, disconnect the instrument or signal source from the Input jack to prolong bafteiy life. • When the unit isrwttobeusedforanerterxtedperiodoftime. disconnect aid remove the battery from the battery compartment to avoid any possfole leakage. • When the LED becomes dim or the performance of the unit seems less than optimum, replace the battery. • For extended time use, it is advisable to use a Peavey AC adaptor to power the effects unit. PEAVEY ELECTRONICS CORP. 711A STREET/MERMAN, MS 39301/U.SA PRINTED IN U.SA THJEPHŒ (601)48^5365/TELEX 504115 #80300675 *>1988 DEPn-16 SJEREO EFFECTS PROCESSOR" • Full bandwidth frequency response • “Studio Quiet” 12 bit A/D/A • Expanded dynamic range • 16-position Delay Select Switch • Proprietary custom VLSI design • Stereo outputs • Silent FET effects switching The DEP™-16 Stereo Effects Processor is an ultra-quiet, studfcxjualily digital effects processor. Sixteen delay ranges, along with LFO, regeneration and effect level controls, allow the creation of a variety of effects including chorus, flanging, delay, and vibrato. Full 12-bit A/D quantization is made possible by Reave/s proprietary VLSI custom IC along with subminiature surface-mount techniques. Superior sound quality and “no compromise" attention to detail have made the DEP-16 one of today's finest and most flexible floor delay pedals. Many large rack-mount delays fall short of the sparkling crystal-clean delay sound of the DEP-16. High headroom line-level capability allows the DEP-16 to be patched into high level effects loops for the best in "posf-delay effects. Rugged die-cast construction along with silent FET, ”soft-touch" effects switching and "effect on” LED indication complete the very musical DEP-16. ■¿И!Ы<М!Я OUTPUTAJACK OUTPUT В JACK DEPTH/SPEED AC ADAPTOR JACK INPUT JACK EFFECT LEVEL EFFECT SWITCH- STEREO EFFECTS PROCESSOR DEP-16 16 POSITION SELECT / - REGENERATION — “EFFECT ON” LED INDICATOR (BATTERY ACCESS ON BOTTOM) DEPTH/SPEED: This control provides a dual adjustment of the LFO modulation depth and speed (frequency). In the full counterclockwise position, the modulation is off. Rotating this control clockwise increases the depth from 0% to 100% (a 4:1 sweep) and simultaneously decreases the speed from 10Hzto0.1 Hz. This synchronized parameter control greatly simplifies the operation of this unit and allows the operator a wide variety of musically pleasing effects. EFFECT LEVEL* Controls the relative volume of the delayed signal or the delay/dry mix. Maximum delayed signal level is obtained by rotating the control fully clockwise. In this position, the level of the delayed signal is equal to that of the direct signal. NOTE: This control affects only the delayed signal. REGENERATION LEVEL- Controls the number of repeats or the "delay time" for the delayed signal. A single repeat is available with the control set fully counterclockwise. Increasing numbers of repeats (or longer delay times) are obtained as the control is rotated clockwise. SELECT: Selects one of sixteen delay ranges. The available delay increases with clockwise rotation of this control with the maximum delay being at the 6 o'clock position, the DEP-16 delay ranges include: Position #1 Position #2 Position #3 Position #4 Position #5 Position #6 Position #7 Position #8 Range #1 Flange #2 Chorus #1 Chorus #2 50ms Delay 75mS Delay 100mS Delay 15QmS Delay Position #9 Position #10 Position #11 Position #12 Position #13 Position #14 Position #15 Position #16 200mS Delay 250mS Delay 300mS Delay 350mS Delay 400mS Delay 500mS Delay 650mS Delay 800mS Delay INPUT JACK: Used as a signal input to the effects unit. This jack also actsasa power switch for the unit when an inshwnent is plugged in. When the effect is not in use, the instrument should be disconnected from this jack to maximize battery life. AC ADAPTOR JACK: Used as an alternative +9 volt power source when batteiy operation is not the most desirable. Use only Peavey £volt AC adaptor or equivalent. OUTPUT A JACK: Used as a Icw-impedance signal output for the "out-of-phase" chorus signal in normal stereo operation. If a dry/direct output is desired from this outp...