Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
You could damage the surface of the transfer belt. 10Pinch the transfer belt tention levers on both sides of the transfer belt. Then, pull them out, as shown below. 11Locate the transfer belt slots inside the printer, one on each side. SETUP GUIDE 11 English 12Hold the handle on the transfer belt and align it with the slots in your printer. NOTE: Keep the transfer belt level, do not turn the transfer belt over otherwise looses toner may be spilled. 13Slide the transfer belt down into the printer. Press it firmly to make sure that it latches into place. 12 SETUP GUIDE 14Firmly push the lock levers on each side towards the top cover, as shown below, to lock the transfer belt into place. CAUTION: If you open the left cover for a few minutes, the imaging unit can be exposed to light. This causes damage to the imaging unit. 15After making sure that the left cover is open, close the top cover. Make sure that it is securely latched. CAUTION: Do not try to close the left cover with the top cover open. This may cause damage to the printer. 16Take the toner cartridges out of their packages. English CAUTION: Do not use sharp objects, such as a knife or scissors, to open the toner cartridges packages. You could damage the surface of the toner cartridges. 17Holding both sides of the cartridges, gently roll them from side to side to distribute the toner. 18Place the toner cartridges on a flat surface as shown and remove the paper covering the toner cartridge by removing the tape. NOTE: If toner gets on your clothing, wipe it off with a dry cloth and wash it in cold water. Hot water sets toner into fabric. SETUP GUIDE 13 19On the right hand side of the toner cartridge slot is a label that identifies which color cartridge to fit into each slot. C M Y K Black Yellow Magenta Cyan 20Holding each toner cartridge, insert them into their corresponding positions shown in order of Cyan, Magenta, Yellow and then Black. Using both hands, grip the cartridge to insert into the slot. Then hold the handle to slide the cartridge in. M Y K C Grip here. •When the toner cartridges are correctly installed the yellow and black cartridges are not fully inserted. These will be pushed into place when you close the left cover. 14 SETUP GUIDE 21Close the left cover. Make sure that it is securely latched. English If you have installed the toner cartridges wrongly, the left cover will not close properly. Check again to make sure the cartridge colors correspond to those marked on the right hand side. Never use force to close the cover. NOTE: When printing text at 5% coverage, you can expect a toner cartridge life of about 7,000 pages for black and 5,000 pages for color. However, the toner cartridge that is shipped with the printer prints 2,000 pages for black and white, 1,500 pages for color. SETUP GUIDE 15 Step 4. Loading Paper The tray (Tray 1) can hold a maximum of 250 sheets of plain paper. You can use A4 and letter-sized paper. To load paper: 1 Pull the tray out of the printer. 2 Push down on the metal plate until it locks into position. 3 Flex the paper sheets back and forth to separate the pages and then fan them while holding one edge. Tap the edges of the stack on a flat surface to even it up. 16 SETUP GUIDE 4 Load paper with the print side facing up. English Make sure that all four corners are flat in the tray and under the corner brackets as shown below. 5 Do not exceed the maximum stack height. Overfilling the tray may cause a paper jam. SETUP GUIDE 17 6 Pinch the paper guide as shown and move it toward the paper until it lightly touches the side of the stack. Do not press the guide too tightly against the edge of the paper; the guide may bend the paper. NOTE: If you want to change the paper size in the tray, refer to the User’s Guide of your printer supplied in the CD-ROM. 7 Slide the tray back into the printer. NOTES: • Do not push the width guide far enough to cause the material to warp. • If you do not adjust the width guide, it may cause paper jam. 18 SETUP GUIDE Step 5. Connecting a Printer Cable You need to connect your printer to the computer with either a parallel interface cable or a Universal Serial Bus (USB) cable. English Using a Parallel Cable NOTES: • The parallel port may not be available depending on your country. • To connect the printer to the parallel port of the computer requires a certified parallel cable. You need to buy a IEEE1284 compliant cable that is within 3m in length. 1 Make sure that both the printer and the computer are turned off. 2 Plug the parallel printer cable into the connector on the back of the printer. Push the metal clips down to fit inside the notches on the cable plug. To the parallel port on your computer 3 Connect the other end of the cable to the parallel interface port on your computer, and tighten the screws. See the User’s Guide of your computer, if you need help. SETUP GUIDE 19 Using a USB Cable NOTE: Connecting the printer to the USB port of the computer requires a certified USB cable. ...
Dieses Handbuch ist für folgende Modelle:Drucker - CLP-500 (9.71 mb)
Drucker - CLP-500G (9.71 mb)
Drucker - CLP-500N (9.71 mb)
Drucker - CLP-500NA (9.71 mb)