Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
An optional drain/overflow kit is available for installation on the bath. 32'' 32'' 60'' 18-1/2" 18-1/2" 84-1/2'' 36'' 24'' 24-1/2'' 14-1/2'' 9-3/8'' SIDE VIEW END VIEW WITHOUT END VIEW WITH BODY SPRAY JETS BODY SPRAY JETS SPECIFICATIONS TOTAL WEIGHT/ FLOOR OPERATING PRODUCT WATER ELECTRICAL DIMENSIONS MOTOR/PUMP LOADING GALLONAGE WEIGHT PRESSURE REQUIREMENTS 60" (1524 mm) L 115 VAC 805 lb 38 U.S. gal 238 lb 40 psi min. 115 VAC 32" ( 813 mm) W 3450 RPM/10 AMP (366 kg)/ (144 liters) (108 kg) (2.8 Bar) 15 AMP 84-1/2" (2146 mm) H 60 Hz 60 lb/sq. ft. 60 Hz Single Phase (293 kg/sq. m) Requires dedicated separate circuit Use installation instructions provided with product. Product specifications are subject to change without notice. Optional Features: Trim Kit, Timer, Drain/Overflow Kit, Lamp Package, Pillow, Optica 300 Shower Mixer Valve and SteamPro™ 120 Steam Generator Important: Read complete instructions before beginning installation. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only. Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product. All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure. HEADER ON EDGEBLOCKING REQUIRED IF UNITIS INSTALLED IN SECTIONS 16" 33-1/4" 26" 32" 21" 83" 62" 25" 1x2 12" 60-1/4" FRONTOF DOUBLE STUDSSUB-FLOOR 90. 12" 16" FRAMING DETAILS (RIGHT HAND SHOWN) 12" x 4" DRAIN CUT-OUT 90. Framing and Support The optional drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of approximately 805 pounds (bath, water and bather) or 60 pounds per square foot. If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior to installing the bath. The use of materials that shim or provide a level installation are allowed provided the method used will insure a level bath that is supported from the bottom. Materials that may be used are a floor leveling compound, mortar, plaster or minimal expansion structural foam having a density of a minimum of 5 lbs./cubic ft.; however the bath must remain level in order for it to drain properly and the foam feet must make full contact with the mortar, plaster or structural foam foundation. (The bath must be supported as outlined above.) Both sides of a joint or splice of subfloor should be level to each other. When attaching baths with flanges to stud wall, use shims to fill any gaps between the bath flange and studs. The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added weight must be fully self-supporting. The protective film liner inside the bath is used to prevent damage to the finish from shoes, tools, etc. during installation. Before installation, remove liner to inspect for any defects, reapply and do not remove until final cleanup. The bath unit should be installed after construction of the studwall and rough plumbing is in place. The bath may be installed as a single unit or, if necessary, disassembled and installed in three sections. It is important that the framed pocket be plumb and square and that the framing members be located as detailed in the framing illustration. If the bath unit is to be installed in an existing bathroom studwall, additional studs must be added to the dimensions shown. Rough Plumbing HEADER DETAIL SHEET ROCK SHEET ROCK INSERT 83" 84-1/2" TO 84-3/4" BATH SHOWER HEADER 2" X 4" SHEET ROCK SHOWER SURROUND 1" X 2" SIDE DETAIL (TOP VIEW) DOUBLE 2" X 4" SHOWER SURROUND DRILL CLEARANCE HOLE CAULKING WALL STUD WOOD ENCLOSED WITH FIBERGLASS 1/4" - 20 STUD WALL DETAIL BLOCKING MASKING TAPE The locations of the valves, fill spout and shower head should be marked and drilled before the bath unit is placed in position. Where access to connections is limited, allow enough flexibility in the supply lines for easier positioning of the valves after the unit is in pla...