Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The B-411 has been developed for issuing various kinds of bar codes. The B-411 adopts a state of the art thermal printer so that it produces less noise and more clearly printed characters. This manual contains information about the general set-up and maintenance of the B-411 printer, and should be read carefully to obtain maximum performance from your printer. Since ample consideration has been given to safety, there is no danger of damaging the printer by erroneous operation. Should you have any questions concerning the printer, please refer to this manual. Be sure to keep this manual for future reference. PRECAUTIONS 1. Clean the cover by wiping with a dry cloth or a cloth soaked with detergent and thoroughly wrung out. NEVER USE THINNER OR OTHER VOLATILE SOLVENT for cleaning. 2. DO NOT POUR WATER directly on the printer. 3. When in use, avoid locations subject to vibration and direct sunlight. 4. Properly use the TEC-specified labels. 5. DO NOT STORE the labels, in locations exposed to direct sunlight, high temperature, high humidity, dust, or gas. APPLICABLE MODEL EMl-33017 1. SPECIFICATIONS 1.1 PRINTER —---Model Item —— B-411 Power Requirement Ni-Cd battery (DC 13.2V) Capacity: 19.7mm (500") or 1.4AH Charging time: 7—8AH (Rechargeable a minimum of 300 times) Temperature Limits 5*C to 40*C (41 *F to 104*F) Relative Humidity 25% to 85% RH (no condensation) Print Head Thermal Print Head (6 dots/mm) Printing Method Thermal Direct Print Speed 25.4mm (1")/sec. Available Printing Width 46.8mm (1.84"), 72.2mm (2.84”), 97.6mm (3.84") Bar Code Format Codabar, ITF, CODE39 Parallel only (Barcode height is less than 139 dots) Type Fonts Standard 1 (8 x 18) dots Standard 2 (16X24) dots Bold 1 (8X18) dots Bold 2 16x24) dots 3/4" character (38 x 75) dots Graphic Font (8X12) dots Interface t Serial Interface (RS-232C) 1.2 PAPERS "----^^Paper Type Item Thermal Paper (Label) Width Length (Pitch) Thickness Roll Diameter 53.8mm (2.12"), 79.2mm (3.12*), 104.6mm (4.12”) Max. 998mm (Max. 39.3") 0.14mm—0.15mm (0.0055"-0.0059”) 52mm (2.04") max. 1.3 INTERFACE Item Interface Electronics specification RS-232C Baud rate 9600bps or 19200bps Protocol XON/XOFF, 8 bit Data, Non Parity, Stop bit = 2 bit Signal TXD, RXD, RTS, CTS ЕМ1 -33017 1.4 BATTERY CHARGER Use a battery charger having the following specifications. Item Specification Input Voltage AC120V±10% Output Voltage DC 16.0 V Safety Standard Complying with UL and CSA Charging Time 8 hours ± 10% (13.2V 1.4AH Battery) 1.5 DIMENSIONS (APPROXIMATE) Weight 1.7kg (3.74 lbs.) ЕМ 1-33017 2. OVERVIEW 2.1 FRONT VIEW 2.2 REARVIEW Auxiliary Handle EM1-33017 2.3 OPERATION PANEL ERROR O BATTERY □ PRINT □ FEED CD ON POWER OFF CllP r _oy ERROR Indicator (Green) Lights when the printer does not operate correctly. BATTERY Indicator (Orange) Lights when the battery voltage drops. (Replace the battery) PRINT Indicator (Green) Lights for one second when the power is turned ON. Lights while printing or issuing labels. FEED Button This button is used to feed the labels. POWER Slide switch Power supply switch for the printer. 3. INSTALLING THE PRINTER 3.1 HOW TO INSTALLING AND ADJUST THE SHOULDER STRAP Pass the end of the Shoulder Strap through the tab of the printer from the inside, then pass it through parts A, B and C as shown in the figure. After adjusting the length of the strap, insert the loose end of the strap into the shoulder pad. EM 1'33017 3.2 REPLACING AND INSTALLING THE BATTERY To replace the battery: If the Battery Indicator on the operation panel lights, turn the power OFF, pull up the lock button, slide the battery to the right to remove it. Replace the battery. To Install the battery: Align the left edge of the battery with the line of part A, and slide the battery to the left to lock it in place. (At this time, push the battery until a click is heard from the lock button.) 3.3 CHARGING THE BATTERY Turn OFF the printer power. Open the jack cover and connect the battery charger plug to the printer. It requires B hours to charge the battery. 4. LOADING PAPERS The printer prints labels of the thermal paper. 1) Turn the power off and open the label panel and roll cover. 2) Load the roll paper and pass the leading part of the paper into the printer. 3) Lift the print head and puli out the paper. Thermal Head CAUTION: Use only designated paper, or trouble may result. EM 1-33017 4) Push down the pinch roller lever, pass the paper through the printer, and pull out the paper from under the label panel. Pinch Roller Lever Label Panel 5) Align both sides of the paper with the left and right label guides (red marks) of the print head. Make sure that there is no sag between the thermal head and the pinch roller. Label Guide Thermal head Pinch Roller Paper 6) Close the label panel and roll cover. 7) Turn the power ON and press the FEED button to ensure that the printer operates normally. CAUTION: Aft...