Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Bacharach Dateigröße: 233.79 kb Dateiname: Unterrichtssprache:

Use of a different battery may have a detrimental effect on the alarm operation. The 9 volt battery is not rechargeable. If the 9 volt battery is missing, disconnected, or if the battery’s power is low, red LED flash will occur once every 15 seconds, accompanied by an audible beep. If this happens, the battery must be replaced. IMPORTANT: Constant exposures to high or low humidity may reduce battery life. A good safety measure is to replace the battery at least once a year, or at the same time as you change your clocks for daylight saving time. Battery Alarm Removal If tamper resist feature resist feature description instructions. Remove the alarm from the mounting plate alarm in the direction of the “OFF” To disconnect the AC Quick-Connector squeeze the locking arms on the sides while pulling the away from the bottom of the alarm (see Figure 2). FOR ALARMS EQUIPPED WITH 9 VOLT BATTERY BACKUP After the alarm has been removed, you can open the battery door and replace the battery. Battery installation instructions are provided on the inside of the battery When installing the battery, orient the battery as shown unit label. Press the battery reminder tab down into the battery compartment and install the battery (see Figure 4). FIGURE 4 BATTERY REPLACEMENT CAUTION! If the battery reminder tab is not held down in the battery compartment by the battery, the battery door will not close, the AC Quick-Connector will not attach to the alarm, and the alarm will not attach to the mounting plate. After installing or changing the battery, reinstall your alarm. Test your alarm by using the Test/Reset button and check that the green “Power” LED is on. Maintenance CAUTION: This unit is sealed. The cover is not removable. To keep your alarm in good working you must follow these simple steps: • Test the alarm once a week by pressing Reset button. • Vacuum the alarm cover once a month to remove accumulated dust. • Never use detergents or solvents to clean the alarm. Chemicals can permanently damage or temporarily contaminate the sensor. • Avoid spraying air fresheners, hair spray, paint aerosols near the alarm. • Do not paint the unit. Paint will seal the vents and interfere with proper sensor operation. Move the CO Alarm to a remote location, to prevent possible damage or contamination of the sensor, prior to performing any of the following: • Staining or stripping wood floors or furniture • Painting or wall-papering • Using aerosols or adhesives WARNING: Reinstall the CO Alarm as soon as possible to assure continuous protection. The following is a list of substances that at high levels can damage the sensor or cause temporary readings that are not carbon monoxide readings: Ethylene, ethanol, alcohol, iso-propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen sulfide, sulfur dioxides. Also most aerosol sprays, alcohol based products, paints, thinners, solvents, adhesives, hair sprays, after shaves, perfumes, auto exhaust (cold start) and some cleaning agents. Carbon Carbon Monoxide Procedure WARNING: Activation of the CO Alarm indicates the presence of Carbon Monoxide(CO) which can kill you. 1) Operate the Test/Reset button; 2) Call your emergency services ( Fire Department or 911) ; PHONE NUMBER 3) Immediately move to fresh air - outdoors. Do a head count to check that all persons are accounted for. Do not re-enter the premises until the emergency services have arrived, the premises have been aired out, and the alarm remains in its normal condition. 4) After following steps 1-3, if the alarm reactivates within a 24 hour period, repeat steps 1-3 and call a qualified appliance technician to investigate sources of CO from fuel burning equipment and appliances, and to inspect for proper operation of equipment. PHONE NUMBER If problems are identified during this inspection, have the equipment serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturer’s instructions, or contact the manufacturer’s directly for more information about CO safety and the equipment. Make sure that motor vehicles are not, or have not been, operating in a garage attached or adjacent to the residence. Never restart the source of a CO problem until it has been corrected. Never ignore the sound of the alarm! Carbon Replacement of Seven years after initial every 30 seconds to indicate alarm. A label has been provided that on it. Write the replace-by date on the it to the front of the alarm so it is visible after mounting. date written on the label should be cumulative power. REPLACE IMMEDIATELY! IT WILL NOT DETECT CO IN THIS CONDITION! General CO Information Carbon monoxide (CO) is a colorless, odorless, and poison gas that can be fatal when inhaled. CO inhibits the blood’s capacity to carry oxygen. Periodically review this alarm manual and discuss your CO alarm emergency procedure with all the members of your family. Never ignore a CO alarm. A true alarm is an indication of potentially dangerous l...

Herunterladen

Geben Sie zwei Ziffern: