Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
HOW TO INSTALL THIS EXTINGUISHER • Do not mount the extinguisher on drywall or plaster without adequate support. Use strong screws or bolts to mount the bracket securely into solid wood or metal that can support it, like a wooden partition stud. Secure mounting is needed so you can remove the extinguisher quickly and easily in an emergency. Also, if the extinguisher is not held securely, it could drop to the floor and injure people or damage the extinguisher. • DO NOT BREAK THE SAFETY SEAL! This seal prevents accidental discharge of the fire extinguisher. Break the seal only in an emergency before using the fire extinguisher. INSTALL THE MOUNTING BRACKET ON A WALL 1. The extinguisher has a bracket for wall mounting. 2. Install the mounting bracket on a wooden stud or other solid surface that will support the weight of the extinguisher using the screws or bolts you purchased. NOTE: Since wall surface types vary, mounting screws are not included. Purchase screws or bolts specifically designed for the surface on which you will mount the fire extinguisher. The fire extinguisher label lists its maximum weight. Mounting screw head type should be #8 pan on round head screws with #8 flat washers. 3. After installing the mounting bracket, replace the extinguisher on the bracket with the label facing outward, so the label can be easily read. Wrap the bracket strap around the cylinder and snap the buckle closed. OR INSTALLING THE MOUNTING BRACKET IN A MARINE CRAFT According to the NFPA Standard 302 (Fire protection Standard for Pleasure and Commercial Motor Craft): • On marine craft, portable fire extinguishers shall be located to be readily accessible. Extinguishers shall be secured with a marine bracket to permit immediate release. • On marine craft, extinguisher agent cylinders shall be mounted a minimum of 2 inches (5 cm) above moist or wet surfaces to reduce the danger of corrosion. CHECKING AND INSPECTING THE FIRE EXTINGUISHER • DO NOT CHECK THE PRESSURE OR TEST THE FIRE EXTINGUISHER BY SQUEEZING THE LEVER, EVEN BRIEFLY. ONCE USED, IT WILL GRADUALLY LOSE PRESSURE AND WILL NOT BE FULLY CHARGED FOR USE IN AN EMERGENCY. • When the pointer drops into the red area, the extinguisher may still be pressurized, but must be recharged. 1. Inspect the extinguisher once a week. Remove the extinguisher from the mounting bracket and inspect the gauge. If the yellow pointer is in the GREEN area, the extinguisher is properly pressurized and ready to use. If the pointer drops into the RED area, the extinguisher has lost some pressure and should be replaced. 2. Check for signs of damage or misuse. Make sure you can still read all the text on the label. Carefully examine the surface of the extinguisher for corrosion. You can help prevent corrosion by cleaning the extinguisher if it gets wet or dirty. If you notice corrosion during the warranty period, return the unit to First Alert® (see "Limited Warranty" at the end of this manual). 3. Make sure the tamper indicator ("safety seal") is still intact and the nozzle is clean and unobstructed. 4. When you finish inspecting the extinguisher, always put it back securely into the mounting bracket. For more information about fire extinguishers, consult the NFPA Standard #10, "Portable Fire Extinguishers," available from the National Fire Protection Association, Inc., Batterymarch Park, Quincy, MA 02169, USA. 1 HOW TO OPERATE YOUR FIRE HOW TO CLEAN AFTER USING A FIRE EXTINGUISHER IN A FIRE EMERGENCY EXTINGUISHER NOTE: The powder spray from the extinguisher may spread over a wide area, and may soil upholstery, carpets and walls. • Make sure your extinguisher may be safely and effectively used on the small fire you want to fight. Always use extreme caution when fighting any fire. Fight a fire only where there is a clear escape path to allow you to get out safely if the fire gets worse. • Avoid breathing smoke an...
Dieses Handbuch ist für folgende Modelle:Alarm - FE5GRR (380.91 kb)
Alarm - FE5GR (380.91 kb)
Alarm - FE1A10GR (380.91 kb)