FT-800 SERIES DISHWASHER FOOD EQUIPMENT • Water and energy saving design through reduced water and tank heat usage and automatic pump shut down control through conveyor. • Common water, drain, electric and steam connections. • Exclusive load end flush system. • Built-in integral wiring channel. • Automatic temperature control and positive low-water heater and pump seal protection. • Built-in inherent motor overload protection with manual reset. • Built-in vent ducts—dampers and drip control. • I

Remove 7/8" diameter cap plug(s) for 1/2" trade size conduit fittings from the rear of the enclosure. Strain relief fittings must be provided for all wiring. — VFC1 — VFC2 — BSTR1 — BSTR2 — DPS1 — DPS2 — RPS1 — RPS2 DETERGENT DISPENSER TRANSFORMER PRIMARYSECONDARY RINSE AGENT DISPENSER CHEMICAL SANITIZER DISPENSERRIGHT SIDE OF CONTROL AREA TRANSFORMER PRIMARYSECONDARY GROUND LUG Fig. 22 – 15 – SETUP (All Models) Sanitizing Mode • With the machine OFF, press the ON key. • Immediately press and ho

B (Feb. 2005) POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE. FOR YOUR SAFET

11). NOTE: DO NOT use Teflon tape on gas line pipe threads. For gas line pipe connections, use LOCTITE 565, Hobart part 546292, or a flexible sealant suitable for use with Natural and Propane Gases. The appliance and its gas connections must be leak tested before placing the appliance in operation. Use soapy water for leak test. DO NOT use open flame. The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition). C

6) Repeat steps 4 and 5 for each digit. a. After pressing ENTER on the fourth digit, you will immediately return to the ENTER SECURITY CODE? screen. 7) You will know you entered the code correctly if the letter in the lower left corner reads M. Refer to Machine Operation and Programming Security Levels on page 15 for more details on other letters that may appear. a. If it does not match, repeat steps 3 through 7. b. If it does match, continue to step 8. 8) Press the UP or DOWN keys repeatedly un

2007) TABLE OF CONTENTS OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 3 Machine Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tank Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Upper arm nozzles point downward, and lower arm nozzles point upward. Arms in the prewash chamber each have two tubes (the slightly longer arm goes below). The arms with five tubes fit in the upper brackets, and the arms with four tubes fit in the lower brackets. To install arms, slide manifolds on the guides toward the rear of the machine (Fig. 26). Then latch arms in place (Fig. 27). Fig. 25 Fig. 26 Fig. 27 Replace the pump intake screens, strainer pans, and strainer baskets. Rehang the curtai

C (Mar. 2000) Operation and Care of FT900 SERIES DISHWASHERS SAVE THESE INSTRUCTIONS OPERATION MACHINE PREPARATION — Check before beginning operation. Raise the machine doors and make sure all components are in their proper operating positions. Pump Intake Screens must be put on Strainer Pans must be in place on top of Strainer Baskets must be in place in holders at each pump intake (Fig. 1). each tank (Fig. 2). Strainer Pans (Fig. 3). Fig. 1 Fig. 2 End Caps must be correctly installed at Wash A

Right to Left . Left to Right VOLTAGE . 208/60/1 . 240/60/1 . 380/60/3 . 208/60/3 . 240/60/3 . 480/60/3 . 600/60/3 MODEL . CL54e – Dishwasher OPTIONS AT EXTRA COST . Stainless steel pressure-less 15 KW or 30 KW booster heater . Higher than standard chamber ACCESSORIES . Stainless steel vent hoods . Direct drive unloader . Side loader . Blower-dryer . Drain water tempering kit Specifications, Details and Dimensions on Inside and Back. CL54e DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOB

63 Exhaust Requirements – Cubic Feet per minute Entrance End 200 Discharge End 175 Peak Rate of Drain Flow – Gallons per minute. (Initial rate with full tank) 38 Shipping Weight Crated – Approximate lbs. 1127 AVAILABLE OPTIONS AND ACCESSORIES . . . Flexibility is synonymous with Hobart CLeR dishwashers. If your operation demands a dishwasher with a vent hood, an extended hood . . . a power scrapper, just specify the combination of options that suit your needs. DDU38e Direct Drive Unloader. Cente