Stimmen - 5, Durchschnittliche Bewertung: 3.4
(
)
)
|
Anleitung Zusammenfassung
As a result, water may collect in the base of the appliance and trigger the anti- flood system. Changing a dishwashing cycle 3 If you would like to change the dishwashing cycle before closing the dishwasher door, briefly press the button for the new dishwashing cycle. If you would like to change the dishwashing cycle after the cycle has commenced, proceed as follows: 1 Hot steam may escape when the dishwasher door is opened. There is a risk of scalding! Carefully open the door of the dishwasher. 0 1. Open the door of the dishwasher. The dishwashing cycle will stop. 2. Press the button for the new dishwashing cycle and hold it down. First, the indicator for the dishwashing cycle that is currently running will flash. After several seconds only the indicator for the new dishwashing cycle will be flashing. Operating Instructions 3. Release the cycle button. 4. Close the dishwasher door. The newly selected dishwashing cycle will commence from the beginning. Interrupting the dishwashing cycle by opening the dishwasher door 0 1. Open the door of the dishwasher. The dishwashing cycle will stop. 2. Close the dishwasher door. The dishwashing cycle will continue. Cancelling the dishwashing cycle 0 1. Open the door of the dishwasher. 2. Press function buttons 2 and 3 for approx. 1 second and keep them pressed. The LED indicators for all programme buttons (and the button for the delay start timer if present) light up. The LED indicators and any option buttons that are present only light up if they are activated. 3. Release the function buttons. The dishwashing cycle has been cancelled. 4. Switch off the dishwasher by pressing the ON/OFF button. Load Sensing – Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and/or lower basket, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved. Operating Instructions Switching off the dishwasher If the acoustic signal has been enabled, a continuous tone will sound for 15 seconds at the end of the programme. 1 Hot steam may escape if the door is opened immediately after the programme has ended. Therefore: 0 1. Open the door carefully. 2. Switch off the dishwasher by pressing the ON/OFF button. All display indicators will go out. If you do not switch off the dishwasher, the acoustic signal will sound again 3 minutes later and 6 minutes later. 3 Removing the dishes • Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool before they are removed. • Leave the dishes in the dishwasher for approximately 15 minutes following the end of the programme to enable better drying and cooling down of dishes. • Empty the lower basket first, then the upper basket. This will avoid water spots, which are caused by remaining water in the upper basket dripping onto the dishes in the lower basket. Care and Cleaning 1 Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Operating Instructions Cleaning the Filter 3 The filters should be checked and cleaned regularly. Dirty filters will give poor wash results. 0 1. Open the door, remove the lower basket. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about . a turn anti- clockwise and remove. 4. Take hold of the coarse/fine filter (1/2) by the handle with the hole and remove from the microfilter (3) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (4) from the base of the washing compartment and clean both faces thoroughly 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 1 The dishwasher must not be used without filters under any circumstances. Operating Instructions What to do, if ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee. ...Error messages are displayed. If your appliance is equipped with an optical floor signal, in the event of an error a dot-shaped optical signal will flash on the floor. 3 Errors will only be indicated acoustically if the acoust...