Login:
Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Anleitung Briggs & Stratton, modell A07708-0412-0

Hersteller: Briggs & Stratton
Dateigröße: 2.04 mb
Dateiname: 70db2b03-2238-4c88-90e8-0ecda670e2b2.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Connect length of garden hose to water inlet of pump. 4. Add *RV antifreeze to hose as shown. 5. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 6. Remove garden hose from water inlet of pump. 7. Reconnect spark plug wire. *Windshield washer fluid may also be used TROUBLE SHOOTING GUIDE CAUSE CORRECTION PROBLEM Add Fuel. No fuel. Engine will not start (see Engine Manual for further engine troubleshooting) Add required amount of oil. Low oil Squeeze gun trigger to relieve pressure. Pressure builds up after two pulls on the recoil starter or after initial use. Move choke to the “Choke” position. Choke lever in the “No Choke” position. Attach spark plug wire. Spark plug wire not attached. Place engine ON/OFF switch in ON position. Engine ON/OFF switch in OFF position. Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time. Move choke to the “No Choke” position. Fuel valve closed Move the fuel valve lever to the “Open” position. No or low pressure (initial use) Spray wand not in high pressure. See How to Use Spray Wand instructions in the Operation Section. Low water supply. Water supply must be at least 5 GPM @ 20 PSI. Leak at high pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Water filter screen clogged. Remove and clean filter. Check with Authorized Warranty Service Center (AWSC.) Defective E-Z start valve. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re-connect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air Air in hose. Choke lever in the “Choke” position. Move choke to the “No Choke” position. Throttle control lever is not in the “Fast” position. Move throttle control lever to the “Fast” position. High pressure hose is too long. Use high pressure hose under 100 feet. CAUSE CORRECTION PROBLEM See How to Use Spray Wand paragraph in the Operation Section. Spray wand not in low pressure. Will not draw chemicals Chemical filter clogged. Clean filter. Make sure end of chemical hose is fully submerged into cleaning solution. Chemical screen not in cleaning solution. Chemical too thick. Dilute chemical. Chemical should be the same consistency as water. Lengthen water supply hose instead of high pressure hose. Pressure hose is too long Chemical build up in chemical injector. Have parts cleaned or replaced by AWSC. Worn seal or packing Have replaced by AWSC. No or low pressure (after period of normal use) Worn or obstructed valves. Have replaced by AWSC. Have replaced by AWSC. Worn unloader piston. Have replaced by AWSC. Worn E-Z start valve. Water leaking at gun/ spray wand connection Worn o...

Dieses Handbuch ist für folgende Modelle:
Hochdruckreiniger - A07708-0412-0 (2.04 mb)
Hochdruckreiniger - A07708-0412-0 (2.04 mb)
Hochdruckreiniger - A07708-0412-0 (2.04 mb)
Hochdruckreiniger - A07708-0412-0 (2.04 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien