|
Anleitung Zusammenfassung
– Press START button 8. The salt refill indicator X goes out. The selected setting is saved. . . . !. . . . . . . . . en 7 Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 12. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator X on the fascia is lit, top up the salt. * depending on model com tponsaelnhtwsgD ienrtetUsing detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. emsysntge nitsofw er atfofng chSitwiSwitching off salt refill indicator/ water softening system If the salt refill indicator X is impaired (e.g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Adjusting the water softening system” and select setting 0. The water softening system and salt refill indicator are now switched off. m Warning Never fill the salt dispenser with detergent. You will destroy the water softening system. Special salt $ en Rinse aid % As soon as the rinse-aid refill indicator P is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the dispenser 1J by pressing and lifting the plate on the cover. – Carefully pour rinse aid up to the max. mark in the filler opening. –Close cover until it clicks shut. –To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid dispensed can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils. – Close the door. – Switch on ON/OFF switch (. The Cleaning display )" flashes. – Press and hold down the START button 8. – Rotate programme selector 0 until the rinse aid refill indicator P flashes. – Release button. The rinse aid refill indicator P flashes and the displays h and ` are lit (= Setting 2). To change the setting: – Rotate programme selector 0 until the required setting has been selected. – Press START button 8. The rinse-aid refill indicator P goes out. The selected setting is saved. Switching off rinse-aid refill indicator If the rinse-aid refill indicator P is impaired (e.g. when using combined detergents containing rinse-aid component), it can be switched off. – Proceed as described under “Setting amount of rinse aid” and select setting 0. The rinse aid refill indicator P is now switched off. en 9 Not suitable – Cutlery and utensils made of wood. – Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof. – Plastic parts not resistant to heat. – Copper and tin utensils. – Utensils which are soiled with ash, wax, lubricating grease or ink. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Glass and utensil damage Causes: – Glass type and glass production process. – Chemical composition of the detergent. – Water temperature of the wash programme. Recommendation: – Use only glasses and porcelain which the manufacturer designates as dishwasher-proof. – Use a detergent which protects utensils. – Take glass and cutlery out of the dishwasher as soon as possible after the programme ends. Loading the dishwasher – Remove large food remnants. It is not necessary to prerinse utensils under running water. – Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down. – parts with curves or indentations are at an angle, thereby allowing water to drain. – the spray arm 1" can still rotate freely. Very small utensils should not be washed in the dishwasher, as they can easily fall out of the utensils basket 1B. Unloading the dishwasher Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled. BasketBasket 1B Utensils en 10 Cutlery basket You should always place cutlery unsorted with the poin...
Dieses Handbuch ist für folgende Modelle:Geräte - 3VK300BC/08 (1.76 mb)
Geräte - 3VK300BC/11 (1.76 mb)