Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Switch on ON/OFF switch (. – Press and hold down the START button 8. – Rotate programme selector 0 until the “Check water supply” display ` flashes. – Release button. To change the setting, – By rotating the programme selector 0, you can switch on intensive drying (End displayh is lit) or switch off intensive drying (End display h is not lit). – Press START button 8. The setting is saved. en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators X and P. If required, refill salt and/or rinse aid. Filters The filters 1* keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. en Spray arm Limescale and dirt from the rinsing water may block nozzles and the bearing assemblies of the spray arm 1". – Check outlet nozzles on the spray arm for blockages. – Remove the spray arm upwards. –Clean the spray arm under running water. –Lock the spray arm into position. Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: – First disconnect the appliance from the power supply. – Remove the filters 1*. – Scoop out water, use a sponge if required. – Loosen screws on the pump cover (Torx T 20) and pull off. – Check inner compartment and remove any foreign objects. – Place pump cover in the original position, press down and screw tight. – Install filters. en Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. a=Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. ... when the appliance is switched on The appliance does not start. – The mains fuse has tripped. – The appliance plug has not been inserted. – The appliance door has not been shut properly. ... on the appliance Spray arm rotates sluggishly. – Spray arm blocked. Cover on the detergent dispenser cannot be closed. – Detergent dispenser overfilled or mechanism blocked by sticky detergent residue. Detergent residue in the detergent dispenser. – Dispenser was damp when filled. “Check water supply” display ` lights up. – Tap turned off. – Water supply interrupted. – Supply hose kinked. – Filter in the water supply blocked. – Switch off the appliance and pull out the mains plug. – Turn off the tap. – Clean filter in the supply hose. – Reconnect power supply. – Turn on the tap. – Switch on the appliance. – Water is left in the appliance at the end of the programme. – Waste water hose is blocked or kinked. – Waste water pump blocked, cover on the waste water pump is not locked in position (see Maintenance and care). – Filters blocked. – The programme has not yet ended. Wait until programme ends or implement “Reset” function. The “Check water supply” display ` flashes rapidly. – Water in the safety system. – Switch off the appliance and pull out the mains p...