Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
during vacations). Disposal of an appliance . If the appliance is removed from its installation site and will not be used, remove the doorlock to the wash cabinet to prevent children from locking themselves in the machine. SAVE THESE INSTRUCTIONS Guide to the dishwasher . Upper spray arm (not visible) . Cutlery tray . Upper basket . Middle spray arm . Air inlet for drying (depending on model) . Lower spray arm . Triple filter system . Data plate . Rinse aid reservoir . Dual compartment detergent dispenser Guide to the dishwasher Control panel . Check / Refill indicators . On . button with indicator light . Program selection . Off . button . Program selector button This operating instruction manual describes several dishwasher models with different indicated settings. The different dishwasher models are named : Standard =32 1/16" (81.5 cm) high dishwashers XXL =33 11/16" (85.5 cm) high dishwashers. Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: . For lowest energy consumption you may connect the dishwasher to a cold water source. . For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. . Make full use of the baskets without overloading for the most economical washing. . Use the correct amount of detergent and rinse aid. Detergent dosage is dependent upon the amount of soiling and type of dishware being washed. See the "Program Guide" for more information. . When using powder or gel detergent, reduce the amount to 2/3 of the normal amount when washing a small load. . Choose a program that best suits the degree of soiling and the type of dishes being washed. Before using for the first time To close the door . Push the baskets in. . Lift the door and push until it clicks into position. . Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue. Before using for the first time Water softener To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal) the water should be softened. The built-in water softener is designed for this purpose. The water softener is suitable for a water hardness up to 70 °d (73 gr/gal). – The water softener requires dishwasher salt. If using "Tab" products which include salt, you should still add salt to the machine to achieve optimal cleaning results. – The dishwasher must be correctly programmed to match the hardness of your water. – Your local water authority will be able to advise you of the exact water hardness level in your area. If the hardness of your local supply is constantly lower than 4 °d (4 gr/gal), you do not need to add water softener salt. However the water hardness level must still be programmed. In areas where the water hardness fluctuates (e.g. 37-50 °d [39-52 gr/gal]) always program the machine to the higher value (in this example 50 °d [52 gr/gal]). If there is a fault, it will help the service technician to know the hardness of your local water supply. Please note your water hardness below: °d (gr/gal) The water hardness was programmed at 1-4 °d (1-4 gr/gal) by factory default. Before using for the first time Programming the water softener The set value is indicated by the flashing rhythm of the upper right During programming, other indicator program indicator (see Table). lights flash and light up each time you press a button. Only the indicator lights in the following operating steps are important for the programming. To exit the programming mode at any time and start over again, turn the dishwasher off with the . button. . Press the . button to turn the dishwasher off. . Press and hold the "Program" button and turn the dishwasher on simultaneously using the . button. Keep the "Program" button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. . Now press the program button briefly twice. The "Intake/Drain" indicator flashes twice at a short interval and the upper right program indicator flashes once at a short interval (factory default). . Press the "Program" button (for at least one second) until the "Intake/Drain" indicator lights up. °d gr/gal Flashing rhythm 1 -4 1 -4 Once short 5 -7 5 -7 2 short 8 -11 8 -11 3 times short 12 -15 12 -16 4 times short 16 -20 17 -21 5 times short 21 -25 22 -26 6 times short 26 -30 27 -31 7 times short 31 -36 32 -38 8 times short 37 -45 39 -47 9 times short 46 -70 48 -73 Once long . Press the "Program" button briefly to select the flashing rhythm corresponding to the water hardness in your area. With each press of the button the value will go up one level. Once the highest value is reached the setting will start again...
Dieses Handbuch ist für folgende Modelle:Geräte - G 5175 (2.73 mb)