Stimmen - 0, Durchschnittliche Bewertung: 5 ( )

Hersteller: Miele Dateigröße: 2.73 mb Dateiname: Unterrichtssprache:

Example: The water hardness is 22 °d. The upper right program indicator flashes 6 times at a short interval. . Press the . button to turn the dishwasher off. Before using for the first time Checking the programmed water hardness . Press the . button to turn the dishwasher off. . Press and hold the "Program" button and turn the dishwasher on simultaneously using the . button. Keep the "Program" button pressed for at least four seconds until the lower right program indicator lights up. . Now press the program button briefly twice. The set water hardness value is indicated by the flashing rhythm of the upper right program indicator light (see Table). . Press the . button to turn the dishwasher off. Before using for the first time Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. Filling the salt container Inadvertently filling the salt container with dishwashing detergent (including liquid detergent) will damage the water softener. Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. If using "Tab" products which include salt, still add salt to the machine to achieve optimal cleaning results and ensure long-term functioning of the water softener. . Remove the lower basket from the wash cabinet and unscrew the salt container lid. When opening the salt container, water will run out. Open the container only to refill salt. Important: The salt container must be filled with 2 quarts (2 l) of water before adding salt for the first time so the salt can dissolve properly. Water does not have to be added with subsequent refills. . Place the provided funnel over the salt container and carefully fill it with salt. The salt container holds approx. 4.4 lbs (2 kg) of salt, depending on the type of salt. . Clean any excess salt from the threads of the container opening. Screw the lid on firmly. . Immediately after each refill, run the " Express" program without a load. This will remove any traces of salt from inside the wash cabinet. Before using for the first time Refill salt message . When the "Salt" indicator light comes on, refill the salt after the program has finished. After the container has been filled, the "Salt" indicator light can remain on for a short time. It will go out once the reactivation process is complete. The "Salt" indicator light is turned off if you have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal)). Immediately after each refill, run the "Express" program without a load. This will remove any traces of salt from inside the wash cabinet. Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents rinse aid is not needed. Adding rinse aid . Press the button in the direction of the arrow until the flap springs open. Pour liquid rinse into the reservoir until it is visible the surface of the screen. The rinse aid reservoir holds approx. 3.7 oz (110 ml). . Press on the flap until you hear it click shut. Failure to close it all the way allows water to enter the reservoir during the wash program. . Clean any spilled rinse aid. The flap will remain closed during normal operation. Rinse aid indicator When the rinse aid indicator first comes on, there will be enough rinse aid left for2-3 washes. . The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling. Before using for the first time Adjusting the dosage The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 0to6. – Use a higher setting if spots appear on dry glassware. . Use a lower setting if streaking appears on dishes or glasses. . Turn the dishwasher off "". . Press and hold the "Program" button and at the same time turn the dishwasher on . Hold the "Program" button until the "Rinse & Hold" indicator comes on. If it does not come on start over. . Press the "Program" button three times. The "Intake / Drain" indicator flashes three times in intervals. The "SaniWash" indicator flashes 3 times in intervals. The rinse aid dosage is adjusted to 3 ml by default. The amount set can be recognized by the flashing rhythm of the "SaniWash" indicator (see table): Dosage in ml Flashing rhythm 0 - 1 Once 2 Twice 3 3 times 4 4 times 5 5 times 6 6 times . Press and hold the "Program" button until the "Intake / Drain" indicator lights up. . Select the desired setting with the "Program" button. Every touch of the button increases the level. The programmed dosage is saved. . Turn the dishwasher off "". Loading the dishwas...

Herunterladen

Geben Sie zwei Ziffern: