Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Haier Dateigröße: 375.79 kb Dateiname: cc2a9869-6dfd-45cc-9633-37bfd5be147e.pdf Unterrichtssprache:

The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig.C). Adjust the upper basket to the higher level and you have more space to accommodate those taller pans and trays in the bottom basket. Shelf Lean tall glasses and those with long stems against the shelf-not against other items to be washed. Place glasses, cups and small bowls on the additional cup rack. The additional cup rack can be swivelled in or out as required(see fig.D) . Knife rack (for DW12-EBM4S) The knife rack clips onto the side of the top basket, giving you the freedom to wash your large sharp knives separately and out of harm’s way (see fig.E) . .5. Lower Rack Upper Rack Load for 12 Standard Settings ( for DW12-EBM4S ) Load for 12 Standard Settings ( for DW12-EBM3S/1S ) fig.A fig.B1 1 2 3 4 fig.B2 fig.C fig.D fig.E GB Turning on the Appliance Starting a wash cycle - Make sure that the plug for the appliance socket. - Make sure that the water supply is turned - Load the dishwasher (see the section entitled, Dishwasher"). - Pour in the detergent (see the section entitled, "Salt, and Rinse Aid"). - Turn the knob located on the right of the control panel in clockwise direction until the number or symbol for the cycle is aligned with the reference mark (see the section entitled, "Wash Cycle Table"). - Press the ON-OFF button, and the ON-OFF light will turn on. At this point, the wash cycle will begin. If you forget to load some of the dishes The wash cycle can be interrupted by pressing the ON-OFF button. You can then load additional dishes and turn the appliance back on. The cycle will start where it left off. At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. Wash Cycle Adjustment Buttons "ECO" Button This button (see "Close-up View - Control Panel", letter " G" ) is used for normal dirty dishes, pots and pans. It is a standard daily cycle. Half load Button This button (see "Close-up View - Control Panel", letter " H" ) makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and electricity. It can be used before setting any of the wash cycles. Please keep in mind that the amount of detergent should also be cut in half. GB .6. Wait a few minutes before unloading handling the dishes and utensils susceptible to breakage. They will also Cancelling or modifying a wash cycle A cycle that is underway can only be modified if for a short time. Otherwise, the detergent may been used, and the appliance may have already drained water. If this is the case, the detergent dispenser must be (see the paragraph entitled, "Loading the Detergent"). Press the ON-OFF button, and the ON-OFF light will turn off. Rotate the knob in clockwise direction to the desired cycle setting (see the section entitled: Starting a wash cycle . Then, turn the dishwasher back on using the ON-OFF button. STOP Rapid Button This button (see "Close-up View - Control Panel", letter " I" ) , when pressed with glassware wash cycle make it possible to run the wash cycle at a lower temperature and eliminates the drying phase. Energy Saving Wash Cycle 1>. DW12-EBM 4S - Use the right amount of detergent: - It is important to try and run the the result will not be cleaner dishes, negaloaded to save on energy. In order impact on the environment. ing and food from caking onto the dishes, cycle. -There is no advantage in rinsing dishes, cookware before placing them in the dishwasher. - Choose the right wash cycle: the choice of cycle depends the type of dishware, cookware and utensils being washed how dirty they are. How to Keep Your Dishwasher in Shape After Every Wash Moving the Appliance After every wash, turn off the water supply to the appliance and If the appliance must be moved, try to keep it in the vertical position. leave the door slightly ajar so that moisture and odors are not If absolutely necessary, it can be positioned on its back. trapped inside. Seals Remove the Plug One of the factors that cause odors to form in the dishwasher is Before cleaning or performing maintenance, always remove the food that remains trapped in the seals. Periodic cleaning with a plug from the socket. sponge will prevent this from occurring. No Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not When You Go on Holiday use solvents or abrasive cleaning products. Use only a cloth When you go on holiday, it is recommended that you run a wash and warm soapy water. cycle with the dishwasher empty and then remove the plug from To remove spots or stains from the surface of the interior, use a the socket, turn off the water supply and leave the door of the cloth dampened with water and a little white vinegar, or a clean- appliance sligh...

Herunterladen

Geben Sie zwei Ziffern: