Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
n Check the fuse. n Is the water supply tap turned on? n Is the water inlet hose connected properly? n Is the pressure of the water supply sufficient? n Is the inlet hose kinked? n Is the filter on the water supply hose blocked? n Is the dishwasher door not closed properly? If water remains inside the dishwasher, check... n the drain hose is not kinked. n the drain syphon is not obstructed. n the dishwasher filters are not clogged. If the dishes are not being cleaned properly, check... n the correct amount of detergent has been added. n there is regenerating salt in the salt container. n the dishes have been loaded correctly. n the selected programme is suitable for the type of dishes and the degree of soiling. ¦ all filters are clean and positioned correctly. n the spray arm nozzles are not obstructed. n there is nothing obstructing the rotation of the spray arms. If the dishes fail to dry or remain dirty, check... n there is rinse aid inside the rinse aid container. n the rinse aid dispenser setting is correct. ¦ the detergent being used is of good quality and has not lost its effectiveness (for example, through incorrect storage, with the box left open). If the dishes show signs of streaking, staining etc. check... n the rinse aid dispenser setting is not set too high. If there are visible traces of rust inside the tank, check... n the cap off the salt container is securely closed and that the water softner setting is correct. ¦ the correct amount of detergent is being used. Certain detergents can be more corrosive than others. n the tank is made of steel and therefore any rust marks are due to external elements (fragments of rust from the tank pipes, pots, cutlery etc.) Special products are commercially available to remove such marks. Error messages Your dishwasher is equipped with a safety system which is able to detect operating faults. These faults flash up on the display by several codes consisting of letters and numbers. Take a note of the codes, turn the appliance off and call Hotpoint Service for technical assistance. Tap off alarm If the H2O code is flashing on the display with a long series of prolonged beeps, it means you have forgotten to turn the water tap on. Turn knob “A” to OFF, turn on the water tap and wait approximately 20 seconds before turning the appliance back on. The wash cycle will start up again after a few minutes. If you are not there when the H2O code appears, the appliance will switch to alarm mode and the code A06 will flash on the display. Turn knob “A” to OFF, turn on the water tap, wait approximately 20 seconds before turning appliance back on. Re-select the wash cycle and the appliance will start up again. If after all the checks, the appliance still does not operate or the problem persists, call Hotpoint Service (see KEYCONTACTS, back page) and inform them of: -the type of problem -the abbreviation of the model name (Mod.) and the relative numbers (S/ N) written on the rating plate located on the inner edge of the door. Switch off at the mains socket and remove the plug. Turn off the water supply. D ISHWASHE. INFORMATION FOR TEST LAB. Load for 12 Standard Settings tests (upper rack at top position) Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the ‘Programme Chart’. The detergent dispenser is located on the inside panel of the door. Loading the Detergent To open lid ‘A’ press button ‘B’. The cleaning detergent should be introduced into the three containers ‘1’, ‘2’ and ‘3’ (See table at the end of the page). After pouring in the detergent, replace the lid, pressing down until it clicks. The Rinse Aid This product makes dishes sparkle more as it improves their drying. The rinse aid container is situated on the inside of the door; it should be filled up when the rinse aid indicator light “F” flashes. Loading the Rinse Aid To open the dispenser turn cap C in the anticlockwise direction and then pour in the rinse aid making sure not to overfill. The amount of rinse aid used for each cycle can be regulated by turning the dose adjuster ‘F’ which you will find under lid ‘C’. There are 6 different settings, the normal dosage is setting 5. D B This basket is equipped with two removable grids: insert the cutlery one by one into the slots, with the handles at the bottom. Position them so that they don't touch. Comp1 Comp2 Comp3 C F A Cycl. Total detergen. Comp.. Comp.. Comp.. EN 5024. See bookle. . 30 gr. 2. . IEC/ DI. See bookle. . 30 gr. 1. 2. * Select the Normal or daily wash cycles (See Programme Chart in the instruction booklet. and press the .extra dry button, if existin. After Sales Service "No company is better positioned to offer an after sales service on a Hotpoint appliance than us - the manufacturer" As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee fo...