Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Simple, reliable, accurate… it allows you to monitor indoor or outdoor temperatures as well as rain fall from one room. While the base unit reads indoor conditions, the remote sensor wirelessly reports outdoor weather conditions back to the base unit for an all-in-one weather display. Plan your work day, play day, every day. Now that's smart! Table of Contents: Battery Installation....................................... 2 Temperature Readings................................ 6 How to Set Up Your Rain Gauge............... 2-4 Temperature Trend Indicators..................... 6 Where to Place Your Rain Gauge............. 3 Temperature Alerts....................................... 7 How to Display Your Rain Gauge.............. 3 Low Battery Indicators.................................. 7 How to Read Your Rain Gauge................. 5 Trouble Shooting.......................................... 7-8 How to View Readings................................ 5 Precautions.................................................... 9 Rain Alert...................................................... 6 Specifications................................................ 8 Rainfall History.............................................. 5 Warranty Information................................... 9 Battery Installation Base Unit Base Unit: The Base Display Unit is powered by 2 AAA batteries (not included). UP MODE DOWN 1. Remove the battery compartment cover located on I -ALERT RE-SYNC HISTORY the back of the unit. 2. Install 2 AAA batteries. 3. Replace the battery compartment cover. 4. Remove any static cling label from the LCD screen. Important: Install batteries in the base unit before installing batteries in the rain cup sensor, or the units' transmissions may not properly connect. Rain collection cup sensor: 1. Remove the 2 screws from the battery compartment cover on the bottom of the rain collection cup sensor and remove the cover. 2. Install 2 AAA batteries (not included) into the battery compartment. 3. Tip: Lithium batteries are recommended in extremely cold or hot locations. 4. Replace the battery compartment cover and the screws. Make sure the door is securely closed to prevent water leakage. Remote Rain Collection How to Set Up Your Rain Gauge Cup 1. Remove any static cling labels from the LCD screen and any tape from the base unit or rain collection cup. Tape or Cardboard 2. Install 2 AAA batteries into the base unit (see Battery Installation section). 3. Install 2 AAA batteries into the rain collector cup sensor (see Battery Installation section). 4. Remove the 2 screws on the bottom of the rain cup sensor and remove the rain cup cover. 5. Remove any tape or cardboard from the rain cup pendulum to allow it to fill and empty when rainfall occurs. 6. Replace the rain cup cover and the 2 screws. Battery Cover 2 How to Set Up Your Rain Gauge (cont.) 7. Place the base unit as close as possible to the rain cup sensor. 8. Press the “RE-SYNC” button on the back of the base unit. The base unit will search for a signal from the rain cup. The “ “ icon appears in the bottom left corner of the LCD to indicate a transmission signal has been sent. 9. The IN temperature reading appears when transmission is successful. 10. If the IN temperature does not appear with 3 minutes, press the “RE-SYNC” button again. If the IN temperature still does not appear, refer to the Troubleshooting Section. 11. The remote will then automatically transmit updated readings to the base unit every 45 seconds. TIP: Press ‘IN/OUT TEMP’ on the back of the base unit to switch between indoor and outdoor temperatures. Where to Place Your Rain Gauge Base unit location: Place the unit indoors in a well-ventilated location away from direct sunlight. Rain Collection Cup Sensor location: 1. Place the rain collection cup sensor on a level, horizontal surface for accurate readings. 2. If desired, use the 2 included screws to mount to a solid surface (such as a fence post or a garden shed. Or use the 2 included spikes to mount to the ground. (Please note the rain cup sensor must be horizontally upright for accurate rainfall readings.) 3. The transmission range of the rain cup sensor is 100 feet. The effective transmission range is vastly affected by obstacles such as walls, sheds, trees, etc. Try various set ups for the best results. Shorten the distance between base and rain cup sensor units when necessary. Place the sensor in a dry, shaded area. Direct sunlight will heat the casing and inflate temperatures readings. Tip: Keep the rain cup sensor at least 3 feet from any obstructions which may affect rain collection. For example, do not place the sensor under a tree, as water dripping from leaves into the rain cup will overstate actual rainfall. Important: Though the rain cup sensor is weather- and frost-resistant, it should never be completely submerged in water or left outside during snowy weather. Also please note the transmitter should not be left outdoors in temperatures at or...