Stimmen - 5, Durchschnittliche Bewertung: 4.6 ( )

Hersteller: Hearth and Home Technologies Dateigröße: 2.86 mb Dateiname: 30086f3e-6a7e-4c90-9990-1cd53afcd970.pdf Unterrichtssprache:

2. Thermostat Location The thermostat’s location will have some effect on the appliance’s operation. When the thermostat is located close to the appliance, it may require a slightly higher temperature setting to keep the rest of the house comfortable. If the thermostat location is in an adjacent room or on a different floor level, you will notice higher temperatures near the appliance. Fire Hazard. WARNING • Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance properly may cause a house fire. September 1, 2008 250-6422E Page 5 R R Castile Pellet Stove D. Inspect Appliance & Components and C. Tools And Supplies Needed Pre-Use Check List Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace: Reciprocating Saw Safety Glasses Channel Locks Framing Square Hammer Electric Drill & Bits (1/4”) Phillips Screwdriver 1/4” Self-Tapping Screws Tape Meausre Plumb Line May also need: Level Vent Support Straps Framing Material Venting Paint Hi-temp Caulking Material Gloves WARNING Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. • Do NOT install substitute components. Report damaged parts to dealer. WARNING • Installation and use of any damaged appliance. • Modification of the appliance. • Installation other than as instructed by Hearth & Home Technologies. • Installation and/or use of any component part not approved by Hearth & Home Technologies. • Operating appliance without fully assembling all components. • Operating appliance without legs attached (if supplied with unit). • Do NOT Overfire Or any such action that may cause a fire hazard. Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions: Fire Risk. 1. Place the appliance in a location near the final installation area and follow the procedures below: 2. Open the appliance and remove all the parts and articles packed inside the Component Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed. 3. All safety warnings have been read and followed. 4. This Owner’s Manual has been read. 5. Floor protection requirements have been met. 6. Venting is properly installed. 7. The proper clearances from the appliance and chimney to combustible materials have been met. 8. The masonry chimney is inspected by a professional and is clean, or the factory built metal chimney is installed according to the manufacturer’s instructions and clearances. 9. The chimney meets the required minimum height. 10. All labels have been removed from the glass door. 11. Plated surfaces have been wiped clean, if applicable. 12. Thermostat or remote has been installed. 13. A power outlet is available nearby. Page 6 250-6422E September 1, 2008 R September 1, 2008 250-6422E Page 7 Castile Pellet Stove 3Dimensions and Clearances A. Appliance Dimensions Figure 7.1 - Top View Figure 7.2- Front View Figure 7.3 -Side View Figure 7.4 - Side View with Top Vent Adapter 11-13/16 in. (300mm) 24-3/4 in. (629mm) 23-5/8 in. (651mm) 28-7/16 in. (722mm) 23-1/4 in. (591mm) 22-15/16 in. (583mm) 15-13/16 in. (402mm) 16-1/16 in. (408mm) 16-5/16 in. (414mm) 28-5/16 in. (718mm) 3 in. (76mm) 30-5/16 in. (770mm) 27-15/16 in. (710mm) 4-1/4 in. (107mm) CL CL Page 8 250-6422E September 1, 2008 R Castile Pellet Stove Straight Back Against Wall Inches Millimeters A Back Wall to Appliance 2 51 B Side Wall to Appliance 6 152 Corner Installation Inches Millimeters C Walls to Appliance 2 51 Vertical Installation Inches Millimeters D Back Wall to Flue Pipe 3 76 E Side Wall to Cast Top 6 152 F Back Wall to Appliance 8 203 Installations with: 3 to 3 inch Top Vent Adapter and 3 to 6 inch Offset Adapter Kit Corner Installation Inches Millimeters G Walls to Appliance 2 51 H Side Wall to Flue Pipe 3 76 Alcove Installation Inches Millimeters Minimum Alcove Height 43 1092 Minimum Alcove Side Wall 6 152 Minimum Alcove Width 38 965 Maximum Alcove Depth 36 914 Dimension to Corner Inches Millimeters I Flue Center Line 10-3/8 264 J Back of Top Vent Adapter 9-1/8 232 B. Clearances to Combustibles (UL and ULC) Fire Risk. Comply with all minimum clearances to combustibles as specified. WARNING Failure to comply may cause house fire. NOTE: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. • Illustrations/diagrams are not drawn to scale. • Actual installation may vary due to individual design preference. J I CL C C D E F G G H H A B R September 1, 2008 250-6422E Page 9 Castile Pellet Stove *L Exception for Horizontal Installations: USA INSTALLATIONS: A non-combustible floor protection is recommended extending beneath the flue pipe when installed with horizontal venting or under the Top Vent Adapter with vertical installation. CANADA INSTALLATIONS: A non-combustible floor pro...

Herunterladen

Geben Sie zwei Ziffern: