Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 HARDWARE PACK 3 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two M10 x .” Allen Bolts (#36) and . .” Washers (#42). Attach a Lock Knob (#23) to the hole underneath the Main Frame. B.) Slide the Sliding Block (#8) onto the Incline Adjustment Bar (#9). Align the hole then secure it with a Knob Lock (#23) to hold the Sliding Block in position. C.) Attach the Incline Adjustment Bar to the brackets on the Main Frame. Secure each end with one M10 x 2 .” Carriage Bolt (#35), . .” Washer (#42), and M10 Aircraft Nut (#44). DIAGRAM 1 4 STEP 2 (See Diagram 2) A.) Attach four Bushings (#27) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 .” Allen Bolt (#37) and . .” Washer (#42). Repeat the same procedure to install the other side. C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest Supports (#7). Align the holes and secure them with one M10 x 6 .” Allen Bolt (#38), two . .” Washers (#42), and one M10 Aircraft Nut (#44). Do not over tighten the nut and bolt. The Supports need to swivel on the Bolt. D.) Attach two Bushings to the pivot on the Main Frame (#1). Loosen and pull the Lock Knob on the Sliding Block (#8). The Sliding Block needs to be able to slide on the Chromed Incline Adjustment Bar (#9). Align the two Seat Support Frames (#6) to both ends of the pivot on Main Frame. Secure them with one M10 x 8 .” Allen Bolt (#39), two . .” Washers (#42), and one M10 Aircraft Nut (#44). E.) Use the Lock Knob on the Sliding Block (#8) to adjust and secure the backrest incline position. 5 STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and . 5/8” Washers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#40) and . 5/8” Washers (#43). DIAGRAM 3 6 STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x .” Allen Bolts (#36), and two . .” Washers (#42). B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls (#24) onto the Tubes from both ends. Plug six Foam Roll End Caps (#25) into the Tubes. C.) Slide the Olympic Sleeve (#20) onto the weight post on the Leg Developer. Attach a Spring Clip (#22) to the Sleeve. DIAGRAM 4 7 STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two . 5/8” Washers (#43). Insert the Arm Curl Stand into the front opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height. B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5). Lock it with a L-shaped Pin (#21). C.) Remove the Pin, Curl Bar Handle and Arm Curl when using the Leg Developer to exercise. DIAGRAM 5 8 9 PARTS LIST KEY NO. DESCRIPTION Q’ty Main Frame 1 Front Stabilizer 1 Rear Stabilizer 1 Arm Curl Stand 1 Leg Developer 1 Seat Support Frame 2 Backrest Support 2 Sliding Block 1 Incline Adjustment Bar 1 Foam Tube 3 Curl Bar Support Frame 1 Curl Bar Handle 1 Seat Pad 1 Backrest Board 1 Arm Curl Pad 1 Curl Bar Handle Grip 2 Axle 1 O 2 3/8” Bushing 2 O 1 .” Bushing 2 Olympic Sleeve 1 L-shaped Lock Pin 1 Spring Clip 1 Lock Knob 2 Foam Roll 6 Foam Roll End Cap 6 O .” x .” Bushing 2 Bushing 16 3 1/8” x 1 5/8” End Cap 1 O 1” Cone-shaped End Cap 1 O 1” End Cap 1 1 5/8” x 2 3/8” End Cap 2 1 5/8” x .” End Cap 12 2” Sliding Block Sleeve 3 Stabilizer End Cap 4 M10 x 2 .” Carriage Bolt 2 M10 x .” Allen Bolt 6 M10 x 1 .” Allen Bolt 2 M10 x 6 .” Allen Bolt 1 M10 x 8 .” Allen Bolt 1 M8 x 2” Allen Bolt 8 M8 x 5/8” Allen Bolt 2 O .” Washer 14 O 5/8” Washer 10 M10 Aircraft Nut 4 10 IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any ...