Stimmen - 6, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
M968951 Rev. 1.4 Certified to comply with ANSI A112.18.1 Recommended Tools Flat Blade Screwdriver Adjustable Wrench Plumbers' Putty or Caulking Channel Locks Pipe Wrench Phillips Screwdriver ROUGHING-IN DIMENSIONS To assure proper positioning in relation to wall, note roughing-in dimensions. 5-5/8" REF. BOTTOM OF TUB 74" FOR HEAD CLEARANCE FINISHED WALL 8-1/8" REF. 4" 6-1/2" 18" OPTIONAL TOP OF TUB RIM 8-3/8" 2-3/8" 1/2" NPT "SEE ILLUSTRATION " 1/2" NPT 1-1/2" REF. 3/4"" TO 2-3/8" SHR TUB OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 80'' SHR. 1/2" NOM. COPPER SWEAT SWEAT INLETS TUB 1/2" NOM. COPPER SWEAT SWEAT INLETS (STOPS) SHR. 1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT INLETS 1/2" NPT 3-3/8" 3-3/8" OUTLETS 1/2" NPT INLETS 4-1/16" 4-1/16" COPPER SWEAT 2" INLETS 1/2" NOM. 4-1/16" 5-7/8" INLETS 1/2" NOM. COPPER SWEAT 3-3/8" THREADED INLETS INLETS 1/2" NPT 5-7/8" OUTLETS 1/2" NPT THREADED INLETS (STOPS) CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. PIPE PLUG 2 1 5 4 3 2 SHR. ELBOW TUB FILLER NIPPLE 7 8 1-1/2" REF. 1 INSTALL VALVE TRIM 1 Figure 1. Figure 2. Figure 3. 3 5 6 4 2 1 Figure 1. Remove plaster guard from valve. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1) and attach with LONG SCREWS (4). Mount ESCUTCHEON SUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORT SCREWS (6). Figure 3. Align PINS (7) on back side of ESCUTCHEON (8) with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5) and press ESCUTCHEON (8) flush against finished wall. Remove pipe cap and plug from shower and tub rough piping. Install SPOUT ESCUTCHEON (1) onto TUB SPOUT (2). Apply sealant or Teflon tape to threads of tub filler nipple. Thread TUB SPOUT (2) onto tub nipple. CAUTION: Protect finish on TUB SPOUT when installing. Install SHOWER ESCUTCHEON (3) onto SHOWER ARM (4). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (4) and thread longer leg of SHOWER ARM (4) into shower elbow. Thread SHOWER HEAD (5) onto SHOWER ARM (4). 2 INSTALL TUB SPOUT, SHOWER HEAD, SHOWER ARM WITH FLANGE CAUTION: Protect finish on SHOWER HEAD and ARM when installing. CAUTION: Protect finish on SHOWER HEAD and TUB SPOUT when installing. PLSTER GUARD 9 5 M968951 Rev. 1.4 "B" "B" 3 ADJUST HOT LIMIT STOP By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP. Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0". HOT LIMIT SAFETY STOP ADJUSTMENT PRY RED RING FORWARD AND ROTATE COUNTER-CLOCKWISE ONE CLICK PRY RED RING FORWARD AND ROTATE CLOCKWISE "A" "A" ADJUSTMENT WHEN WATER IS TOO HOT ADJUSTMENT WHEN WATER IS TOO COLD "RED RING"- HOT LIMIT SAFETY STOP TEMPERATURE SETTING NUMBERS 1 0 1 2 3 4 5 6 2 2.5MM HEX WRENCH 4 4a 4b 4c HANDLE INSTALLATION INSTALL HANDLE ADAPTER INSTALL ADAPTER SCREW INSTALL ADPATER INSTALL HANDLE 1 Push HANDLE ADAPTER (1) onto VALVE STEM (2). Tighten set screw (3) with 2.5mm hex wrench supplied. 3 4 4 5 8 9 6 2.5MM HEX WRENCH 7 1 Align HANDLE (6) and install onto HANDLE ADAPTER ASSEMBLY (7). Tighten set screw (8) with 2.5mm hex wrench supplied to secure HANDLE. Push PLUG BUTTON (9) into set screw access hole in HANDLE (6). With a flat blade screwdriver thread ADAPTER SCREW (4) into HANDLE STEM ADAPTER (1) and tighten. With a flat blade screwdriver thread ADAPTER (5) onto SET SCREW (4) and tighten. 5 SERVICE Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets and MANIFOLD (5). Reassemble CARTRIDGE (4), alternately tightening SCREWS (3). Replace CAP (2) and HANDLE (1). Check flow. If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force. Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off water supply, then: CARTRIDGE INLETS 2 3 5 1 4 M968951 Rev. 1.4 ...