Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
NOTE: When starting the unit in the "AUTO" mode and switching to "MANUAL", the fire must be large enough to turn the ignitor light off (located on the control board). This is a signal that the start cycle is completed and the fire will not go out. MANUAL IGNITION/OPERATION Manual Stove Temperature Mode Fig. 24: Room Temperature Mode: This setting will produce a room temperature of 70 degrees with the distribution blower at medium speed. O O Igniter Switch to "MANUAL" Room Temperature Mode The fire will have to be lit with starting gel and a match, or started automatically, see "Automatic Operation". Turn to "Manual" position when the fire is established. The difference between "AUTO" Room Temperature Mode and "Manual" Room Temperature Mode is that the fire will not go out as the room temperature goes above the control board setting. The unit can only go to low burn and will remain there until it runs out of fuel or until more heat is needed and the feed rate increases. Feed rate adjustments and dial settings are the same as "AUTO" settings. Igniter Switch to "MANUAL" Stove Temperature Mode The advantage of this mode is to allow the operator to have a large viewing fire without blowing extra heat into the room. During operation, with the temperature dial set at #5 or less, the distribution fan will not operate. A #5 on the temperature dial and a #5 on the feed adjuster is approximately 80% output. It is not necessary to operate the distribution blower below this point. Therefore, there can be a higher feed rate ( a larger viewing fire) without an excess of hot air blowing into the room. An example of when to use the Manual Stove Temperature Mode is if you want to watch a large fire and the room is already up to temperature. The Stove Temperature Mode allows you to have a larger fire and a lower sound level, without the distribution blower. NOTE: During the use of this mode, if you keep increasing the temperature dial setting to increase the fire size, the distribution blower will automatically come on when the ESP Temperature reaches 350o F, or 81% output. Fig. 25: This setting will produce a large viewing fire without a distribution blower operating. 16 PC 45 Corn/Pellet Stove MANUAL START UP Starting the Fire Igniter Switch to"MANUAL" (down position) Make sure the unit is plugged into a 120 VAC, 60 HZ electrical source. The power light should be the only light lit. Anytime there is interruption in power at the receptacle, the combustion blower will run for 1 minute after the power is regained. Burning Corn 1. Turn the Feed Adjuster to desired feed rate, approximately #2. 2. Turn the Mode Selector to "OFF" and then to the desired mode. This will reset the control and start the combustion motor. 3. Turn the Temperature Dial to the desired setting. 4. Clean the burnpot and housing, if necessary. 5. Fill the burnpot with corn up to the auger shaft. Then place pellets on top of the corn as high as the shelf area. See corn burnpot shown on left. 6. Add starting gel on top of the pellets, stir gel into the pellets and corn for faster lighting. 7. Light the starting gel with a match and close the door. Operation will begin when the fire reaches the proper temperature. 8. Fill the hopper with corn and remove the ashes as required. Burning Pellets Optional pellet burnpot required to burn pellet fuel. 1. Turn the Feed Adjuster to the desired feed rate, approximately #4. 2. Turn the Mode Selector to "OFF" and then to the desired mode. This will reset the control and start the combustion motor. 3. Turn the Temperature Dial to the desired setting. 4. Clean the burnpot and housing, if necessary. 5. Fill the burnpot with pellets so that the auger tube opening is covered and slopes away from the auger tube opening. See pellet burnpot shown on left. 6. Add the starting gel on top of the pellets. Stir the gel into the pellets for fast lighting. 7. Light the starting gel with a match and close the door. Operation will begin when the fire reaches the proper temperature. 8. Fill the hopper with pellets and remove the ashes as required. Fig. 26 Corn Burnpot Optional Pellet Burnpot "NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR "FRESHEN UP " A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IN USE". Warning Fig. 27 Fig. 28 Shut-Down Procedure To kill the fire or stop burning the stove, turn the Mode Selector to "OFF". This will cause the fire to diminish and burn out. When the fire burns out and the stove cools down everything will stop. NOTE: The combustion blower motor will run for 5 hours after the stove is completely cool. This insures that all fuel in the burnpot and ashes located in the ash pan are completely cold before shut down of the combustion motor. If you pull the plug to shut down the stove, all motors will stop. This may cause incomplete combustion and smoke in the firebox. If the load door is opened the smoke may escape. ...