Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed. TO UNLOCK press both buttons together on hand-held remote control until the light stops flashing. The hand-held remote is now un locked. Control Button Turns Burners On and Off Figure 23 - On/Off Hand-Held Remote Control Unit (GHRCB) THERMOSTAT SERIES (MODEL GHRCTB) The hand-held remote can be operated using either the manual mode (MANU) or thermostatic mode (AUTO) (see Figure 24). To select Fahrenheit/Centigrade mode display, carefully press the °C/°F mode button with the end of a paper clip or similar blunt object. Manual Mode 1. Press the POWER and LOCK buttons together to turn on the hand-held remote control. 2. Press the MANU button to turn on the heater. Turns Remote On Digital Display or Off and Shows Allows You Temperature to Choose and Settings the Manual SettingTurns Burners On or Off Selects Auto SettingDecreases Room Increases Temperature Room in AUTO Mode Temperature Locks System to in AUTO Prevent Accidental Mode Ignition Figure 24 - Thermostat Hand-Held Remote Control Unit (GHRCTB) 113084-01C OPERATING HEATER Continued 3. Press the POWER and LOCK buttons together to turn off the heater. Auto (Thermostatic) Mode 1. Press the POWER and LOCK buttons together to turn on the hand-held remote control. 2. Press AUTO button to select this mode. 3. Set the desired room temperature by pressing the TEMP + or - buttons. 4. Press the POWER and LOCK buttons together to turn off the fireplace Note: Do not leave the hand-held remote in the AUTO mode close to the fireplace. The radiant heat from the fireplace will turn off the fireplace. Ideally, place the hand-held remote in the center of the room facing towards the fireplace. Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode. Safety Features When away from home for an extended period of time or as a child safety feature to prevent accidental ignition of the fireplace, the receiver ON/OFF/REMOTE switch should be in the OFF position. Auto Shutoff Feature 1. If the average room temperature exceeds 82 degrees Fahrenheit (28 degrees Centigrade), the hand-held remote control will perform a safety override and shut the fireplace off. This feature is not available in the MANU mode. 2. The receiver continuously receives signals from the hand-held remote to control the room temperature. If the hand-held remote is misplaced, obstructed, or for any reason cannot transmit to the receiver, the receiver will shut off the fireplace after 8 minutes. Key Pad Lock Feature This feature allows the user to lock/unlock the keypad on the hand-held remote in the MANU or AUTO mode to prevent inadvertent operation (i.e. children operating the hand-held remote control, etc.). The keypad is locked in either on or off. Press the POWER and LOCK buttons together to turn the unit on or off. INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT FLAME PATTERN Figure 25 shows a correct pilot flame pattern. Figure 26 shows an incorrect pilot flame pattern. The incorrect pilot flame is not heating the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down. If pilot flame pattern is incorrect, as shown in Figure 26 • turn heater off (see To Turn Off Gas to Appliance, page 15 • see Troubleshooting, page 19 Note: The pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color. Pilot Burner Thermocouple Figure 25 - Correct Pilot Flame Pattern (Propane/LP Shown) Pilot Burner Thermocouple Figure 26 - Incorrect Pilot Flame Pattern (Propane/LP Shown) BURNER PRIMARY AIR HOLES Air is drawn into the burner through the holes in the fitting at the burner entrance. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean if needed. Blocked air holes will create soot. MAIN BURNER Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off heater and let cool. Remove blockage. Blocked burner flame holes will create soot. 113084-01C CLEANING AND MAINTENANCE WARNING: Turn off heater and let cool before cleaning. CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, pet hair, bedding material, etc. WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage. B...
Dieses Handbuch ist für folgende Modelle:Standbacköfen - SVYD18PRA (711.11 kb)