Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not move the deck or pull out the AC power cord. Changes to an MD made through recording are saved only when you update the TOC by ejecting the MD or changing the deck to standby by pressing the POWER switch. The MD deck uses the SCMS (Serial Copy Management System on page 40) MDs recorded through digital input connector cannot be copied onto other MDs or DAT tapes through the digital output connector. When recording digital signals that have been emphasized (in the higher frequencies) The signal is automatically de-emphasized (with attenuation proportional to the degree of emphasis) and the level of the de-emphasized signal is indicated on the peak level meters. When the deck is recording or in recording pause, digital signals input through one of the DIGITAL IN connectors are output to the DIGITAL OUT OPTICAL connector with the same sampling rate To change the digital input signal to another sampling rate for output (without recording it to an MD), use Input Monitor Function (see page 11). 10EN Recording on MDs Recording on MDs Useful Tips for Recording TIME EDIT/NO AMS ± OFFREC PLAY 0 10 TIMER PHONES PHONE LEVEL POWER ¤ g0 – + • • • •• • • • INPUT NO EDIT/ PUSH ENTER OPEN/CLOSE REC REC LEVEL RL AMS ±DIGITAL YES OPT1 FILTER OPT2 COAX ANALOG • • • • PLAY MODE REPEAT DISPLAY/ CHAR SCROLL/ CLOCK SET TIME (Ppr0) 5 0 1 3 9 7 4 6 2 8 10 • • • • • • • • • • ANALOG INPUT (pr REC¤OPEN/CLOSE Checking the remaining recordable time on the MD Press TIME. • When you press the TIME button repeatedly while recording, the display alternates between the recording time of the current track and the remaining recordable time on the MD. • When you press the TIME button repeatedly while the deck is stopped, the display alternates between total disc playing time and remaining recordable time on the MD (see page 20). Monitoring the input signal (Input Monitor) Before starting recording, you can monitor the selected input signal through the deck’s output connectors. 1 Press ¤OPEN/CLOSE to remove the MD. 2 Set INPUT according to the input signal you want to monitor. When the INPUT switch is set at ANALOG The analog signal input through the LINE(ANALOG) IN connectors is output to the DIGITAL OUT OPTICAL connector after A/D conversion, and then to the LINE(ANALOG) OUT connectors and the PHONES jack after D/A conversion. When the INPUT switch is set to a digital source After passing through the sampling rate converter, the digital signal input through the respective DIGITAL IN connector is output to the DIGITAL OUT OPTICAL connector, and after D/A conversion to the LINE(ANALOG) OUT connectors and PHONES jack. Either “32kHz”, “44.1kHz”, or “48kHz” appears in the display depending on the sampling rate of the digital signal. 3 Press rREC. If the INPUT switch is set at ANALOG, “AD-DA” appears in the display. If the INPUT switch is set at a digital position, “-DA” appears in the display. If “Auto Cut” appears in the display (Auto Cut) There has been no sound input for 30 seconds during recording. The 30 seconds of silence are replaced by a blank of about 3 seconds and the deck changes to recording pause. z You can turn off the Auto Cut Function For details, see “To turn off the Smart Space Function and Auto Cut Function” below. Note that when you turn off the Auto Cut Function, the Smart Space Function is turned off automatically. If “Smart Space” appears in the display (Smart Space) There has been an extended silence of 4 to 30 seconds in length during recording. The silence is replaced with a blank of about 3 seconds and the deck continues recording. Note that new track numbers may not be marked for portions recorded while this function is activated. To turn off the Smart Space Function and Auto Cut Function 1 While the deck is stopped, press EDIT/NO twice. 2 Turn AMS to display the S08 menu, then press AMS. 3 Turn AMS to select “S.Space Off”, then press AMS. 4 Press EDIT/NO. To turn on the Smart Space Function and Auto Cut Function again 1 Do Steps 1 and 2 in “To turn off the Smart Space Function and Auto Cut Function” above. 2 Turn AMS to select “S.Space On”, then press AMS. 3 Press EDIT/NO. Notes • When you turn off the Smart Space Function, the Auto Cut Function is also turned off automatically. • The Smart Space Function and Auto Cut Function are factory set to on. • The Smart Space Function does not affect the order of the track numbers being recorded, even if the blank space occurs in the middle of a track. • If you turn off the deck or disconnect the AC power cord, the deck will recall the last setting (On or Off) of the Smart Space and Auto Cut Functions the next time you turn on the deck. (Continued) 11EN Recording on MDs Recording on MDs Playing back tracks just recorded Do this procedure to immediately play back tracks that have just been recorded. Press (immediately after stopping recording. Playback starts from the first track of the material just recorded. To play from the first track of the MD after recording 1 Pres...