Stimmen - 7, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
3 Press [SET/PRESET] again to confirm. 4 Repeat steps 2 and 3 to set the hour and minute. Example: To change the clock display In clock mode, press and hold [+, VOL] and [–, VOL] at the same time for 2 seconds to select between a 12-hour or 24-hour display. For 12-hour display: AM : “PM” is not displayed. PM : “PM” is displayed. Daylight saving time (summer time) In clock mode, press and hold [SLEEP] to activate or cancel daylight saving time (summer time) function. “DST” is displayed when the function is activated. Synchronising clock with iPod or iPhone time This function allows you to set the clock’s time to be the same time as your iPod or iPhone’s time (Z page 7, “Compatible iPod and iPhone”). Press [TIME SYNC] while an iPod or iPhone is docked unto the main unit. Note: • Exact synchronisation of an iPod or iPhone with the main unit is not possible. There could be a difference of up to 59 seconds between them. • Compatibility depends on the software version of your iPod or iPhone. RQTX1209 ENGLISH ENGLISH 9 99 ENGLISH ENGLISH RQTX1209 Using an iPod or iPhone 1 Pull out the iPod or iPhone support. Adjust the support according to the height of your iPod or iPhone. iPod classiciPhoneiPod touano Gently pull out the iPod or iPhone support. iPod (not included) 2 Connecting an iPod or iPhone. Hold the main unit when connecting or disconnecting the iPod or iPhone. Note: When docking an iPod touch or iPhone for the first time, a message will be displayed on your iPod touch or iPhone if the Memory Loader application has not been installed (Z page 12). Charging an iPod or iPhone The iPod or iPhone charges automatically when connected to the main unit. • See iPod or iPhone display to check its charging status. • If the iPod or iPhone is not being used for an extended period of time after charging has completed, disconnect it from the main unit, as the battery will be depleted naturally. (Once fully charged, additional charging will not occur.) 10 10 Playing an iPod or iPhone 1 Place an iPod or iPhone in the dock and turn it on. 2 Press [SOURCE] to select “IPOD”. 3 Press [4/9] once to start music playback from the iPod or iPhone. Press again to pause playback. 4 Press [2/–, ADJ] or [+/6, ADJ] to skip to the previous or next track. 5 Press and hold [2/–, ADJ] or [+/6, ADJ] to backward or forward search through a track. Note: • If the iPod or iPhone automatically shuffles or skip a track; – Turn off its “Shake” feature (if there is any). – Play the iPod or iPhone using an iPod or iPhone dock adaptor (not included). • For iPod or iPhone operation details, refer to iPod or iPhone’s User Guide. Using the radio Manual tuning 1 Press [SOURCE] to select “RADIO FM”. 2 Press [2/–, ADJ] or [+/6, ADJ] to select the desired frequency. To tune automatically Press and hold [2/–, ADJ] or [+/6, ADJ] until the frequency starts changing rapidly. Automatic tuning stops when it finds a station or when [2/–, ADJ] or [+/6, ADJ] is pressed again. Note: For better reception, extend and change the direction of the FM antenna. 10 Memory preset Memory preset You may store your favourite channels in 5 FM preset channels. Preparation Press [SOURCE] to select “RADIO FM”. Automatic presetting (AP) Press and hold [SOURCE] until “AP” is displayed. Note: • Automatic presetting begins from the current frequency. • Only the first 5 stations detected will be stored. • “AP” will blink continuously until all 5 channels have been set. Manual presetting 1 Press [2/–, ADJ] or [+/6, ADJ] to select the desired frequency. 2 Press and hold [SET/PRESET] for 2 seconds to display the preset number. 3 Press [2/–, ADJ] or [+/6, ADJ] to select a preset number. 4 Press [SET/PRESET] again to confirm. Tuning in to a preset channel Press [SET/PRESET] to switch between preset channels. Using the sleep timer This function enables you to turn off the unit automatically after the set time (only in iPod and radio mode). 1 Press [SLEEP] to activate the timer. 2 Press [SLEEP] again to select your desired time (in minutes). OFF (default) ] 30 ] 60 ] 90 ] 120 Note: Press [SLEEP] once to check the remaining time. Using the alarm You can set two different alarm times. Before setting the alarm, make sure to set the clock (Z page 9, “Setting the clock”). Setting the alarm 1 Press and hold [ALARM 1] or [ALARM 2] until the hour display blinks. 2 Within 10 seconds, press [2/–, ADJ] or [+/6, ADJ] to set the hour. 3 Press [ALARM 1] or [ALARM 2] to confirm. 4 Repeat steps 2 and 3 to set the minutes. 5 Press [2/–, ADJ] or [+/6, ADJ] to select the days of the week: MON-SUN (everyday) ] MON-FRI (weekdays) SAT-SUN (weekend) 6 Press [ALARM 1] or [ALARM 2] to confirm. 7 Press [2/–, ADJ] or [+/6, ADJ] to select the desired alarm mode: “IPOD”, “RADIO” or “BUZZER”. 8 Press [ALARM 1] or [ALARM 2] to confirm. “IPOD” selection: Continue with steps 9 and 10. “RADIO” selection: Continue from steps 11 to 14. Setting iPod alarm 9 Press [2/–, ADJ] or [+/6, ADJ] to adjust the volume level. 10 Press [ALARM 1...
Dieses Handbuch ist für folgende Modelle:Car Audio - RCDC1EG (1.1 mb)