Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Insert a pre-recorded cassette into the slots in the cassette door with the open end facing up and the full reel on the right side. Close the cassette door. 3 4 Press the PLAY (A) button to begin playback. Adjust the VOLUME control 1 and BASS BOOST button 2 as desired. Press the BASS BOOST button 2 to the “in” position to enhance the bass sound. 5 6 To advance or rewind the tape rapidly, press either the F.FWD (AA) 1 or REWIND (®®) 2 button. When you reach the desired point, press the PLAY (A) button 3 to resume normal playback. To pause playback momentarily, press the PAUSE (p) button. The tape movement stops but the tape motor is still running. Press the PAUSE (p) button again to release pause and resume normal playback. CONTINUED ON THE NEXT PAGE 13 OPERATION (CONTINUED) OPERATION (CONTINUED) 7 To stop playback before the tape ends, press the STOP/EJECT (r) button. The PLAY (A) button is released and the tape motor shuts off. 8 When the tape reaches the end, the auto-stop mechanism activates, the PLAY (A) button is released and the tape motor shuts off. Press the STOP/EJECT (r) button to open the cassette compartment and remove the cassette. 14 OPERATION (CONTINUED) OPERATION (CONTINUED) MAKING A TAPE RECORDING This unit allows you to make direct recordings from the radio or CD player to a blank cassette. An automatic recording volume level control (ALC) circuit will automatically control the volume level of your recordings to prevent distortion. 1 2 Open the cassette door and insert a good quality blank cassette tape into the slots on the door, with the open end facing up and the full reel on the right side. Close the cassette door. Slide the Function switch to select the function you wish to record, either CD or Radio, and operate that function according to its own instructions. 3 4 When you are ready to begin recording, press the RECORD (Q) button. The PLAY (A) button will also engage. The tape will begin moving and all of the material from your selected source will be recorded on the tape. To avoid recording unwanted material, such as radio commercials, use the PAUSE (p) button to stop the recording temporarily. Release the PAUSE (p) button to begin recording again. 5 6 When you are finished recording, press the STOP/EJECT (r) button to stop the tape. If you wish to listen to your recording immediately, press the REWIND (®®) button 1 until the tape rewinds to the beginning, then press the STOP/EJECT (r) button 2. Slide the FUNCTION switch 3 to select TAPE/OFF then press the PLAY (A) button 4 to begin playback. 15 CARE AND MAINTENANCE CARE AND MAINTENANCE SAFEGUARD AGAINST ACCIDENTAL ERASURE When a new recording is made, any program material previously recorded is automatically erased and only the new recording remains. To safeguard valuable recordings from being erased accidentally, the cassette and the deck are equipped with a special device. On the back of the cassette there is an erase prevention tab on each side. To prevent accidental erasing, break out these tabs with a screwdriver. If only one side of the tape is to be protected, break out the tab on the left side with the side desired facing you. To record on a tape in which the tab has been broken, place a piece of adhesive tape over that area. TabCover with tape to record againBreak out the tabto prevent recordingSIDE1Tab for side 1Tabfor side 2 NOTE: When a tab is broken out, the record button cannot be depressed. CASSETTE TAPE RECOMMENDATIONS Standard tape lengths have 15 (C-30), 30 (C-60) and 45 (C-90) minutes of recording time on each side. Longer length tapes of 60 (C-120) minutes of recording time on each side are not recommended. Use only high quality tapes. If a problem develops, check the unit first with another cassette to determine if the problem is with the cassette, and not with the unit. If there is any slack in the tape in the cassette, it should be removed before inserting the cassette. Place a pencil in one of the hubs and rotate clockwise until all slack is taken up. 16 CARE AND MAINTENANCE (CONTINUED) CARE AND MAINTENANCE (CONTINUED) This unit is designed to play only compact discs bearing the identifica- tion logo as shown here. Other discs may not conform to the CD stan- Caring for Compact Discs • Treat the compact disc carefully. Handle the compact disc only by its edges. Never allow your fingers to come in contact with the shiny, unprinted side of the compact disc. • Do not attach adhesive tape, stickers, etc. to the disc label. • Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use detergents or abrasive cleaners to clean the compact disc. If necessary, use a CD cleaning kit. • If a disc skips or gets stuck on a section of the compact disc, it is probably dirty or damaged (scratched). • When cleaning the compact disc, wipe in straight lines from the center of the compact disc to the outer edge of the compact disc. Never wipe in circular motions. • dard and may not play properly. • Compact d...