Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The drain must be steam temperature resistant pipe, which average drain temperature is 150°F (65°C). No hose should be used. 65 Installation – Gas Units INSTALLATION GAS UNITS CSG This section provides the installation instructions for the Henny Penny Gas Combi-Steamers NOTE: The installation must conform with local codes or in the absence of local codes, with ANSI Z223.1 latest edition and electrical code ANSI/NFPA No. 70 latest edition. NOTE: For Canadian installations it should be done in accordance with the CAN/CGA B149.1 or.2 installation code and/or local code and the Canadian electrical code, Part 1, CSA C22.1 for the electrical features. Do Not puncture the cabinet with any objects such as drills or screws as electrical shock, or component damage could result. NOTE: The installation of this equipment should be performed by a qualified technician. LOCATION-CSG The proper location of the unit is very important for operation and convenience. Choose a location which will provide easy loading and unloading without interfering with the final assembly of food orders. Adequate clearance must be considered during installation between the unit and combustible walls. Also, clearance should be provided for servicing and operation of the unit. The minimum clearances are as follows: Left Side Right Side Back Side 14” (350mm) 4” (100mm) 4” (100mm) Place the Combi-Steamer on an original Henny Penny stand or on a level and sturdy surface. Recommended stand height is 22” (555mm). Due to the size of the steam generator, the left side of the unit weighs more than the right side. This weight difference must be compensated by placing the lifting device more towards the left side of the unit, or damage to the unit or personal injury could result. 66 Installation – Gas Units (continued) Minor unevenness of the surface/floor can be compensated by adjusting the metal legs of the stand or the CSG appliance. The weight of the units are as follows: CSG-10 556 lbs. (252 Kg) CSG-12 529 lbs. (240 Kg) CSG-20 1015 lbs. (460 Kg) Do Not obstruct the flow of combustion and ventilation air to and from the unit. DO NOT obstruct the ventilation holes in the panels of the unit, as these provide the combustion air for the burner, or damage to the unit could result. VENTILATION-CSG The gas Combi-Steamers all should be located with a provision for venting into an adequate exhaust hood or ventilation system. We recommend you consult a local ventilation or heating company to help in designing an adequate system. NOTE: Ventilation must conform to local, state, and national codes. Consult your local fire department or building authorities. Ventilation of CSG-12: NOTE: The Combi-Steamer CSG-12 is not suitable for connection to Type B Gas Vent and must be installed under a ventilation hood. Your Henny Penny Combi-Steamer CSG-12 is shipped fully assembled. In a second smaller carton you will find a draft hood which has to be assembled to the unit. Ventilation of CSG-12 table top version: The draft hood must be assembled over the two flue outlets at the back of the Combi-Steamer CSG-12. Ventilation of CSG-12 stacked version: The stacked version kit comprises two different draft hoods, one with a single outlet and the second with a double outlet. A flue riser completes the stacked version flue assembly. Fix the single outlet draft hood over the flue outlets of the lower unit. Place the flue riser over the top flue collar of the draft hood. Attach the double outlet draft hood over the flue outlets of the upper unit so that the flue riser projects into the lower opening of this draft hood. Ventilation of CSG-10: The draft hood must be installed over the flue risers on top of the Combi-Steamer CSG-10 when the flue gas is discharged via a Type B gas vent. When the flue gas of a CSG-10 is discharged to a ventilation hood the draft hood will not be installed. Ventilation of CSG-20: The draft hood must be installed over the flue risers on top of the Combi-Steamer CSG-20 when the flue gas is discharged via Type B gas vent. When the flue gas of a CSG-20 is discharged to a ventilation hood the draft hood will not be installed. 67 WATER SUPPLY-CSG CSG The Combi-Steamer should only be connected to a cold water supply which meets the quality requirements by the EPA on drinking water. Soft water must be at least 5 or 6 grains. The recommended water supply pressure is 44 psi, but 22 to 87 psi will work. Should the water pressure exceed 87 psi, a pressure regulator must be installed into the supply line or damage to the unit could result. Both water and gas connections are 3/4” NPT fittings. Be sure to connect to proper pipe. Check label on unit for each. The water connection is done on a 3/4” NPT thread fitting, and a manual shut-off valve must be installed between the main cold water supply and the units supply line. A minimum water conductivity of 20 micro Siemens is required for proper operation, If below this figure the steam generator will over-fill. NOTE: A ch...
Dieses Handbuch ist für folgende Modelle:Dampfgarer - CSB (716.05 kb)
Dampfgarer - CSM (716.05 kb)