Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle. • Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop. • If the installation angle exceeds 30. from horizontal, the unit might not give optimum performance. • This unit is not waterproof and is intended for interior mounting applications only. Exterior mounting of the unit requires use of an ASA approved marine housing. • Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration. • Be sure to remove the control panel before installing the unit. Mounting the Unit This unit can be property installed with a conventional DIN front mount. 1. Slide the mounting sleeve off of the chas- Dashboard sis if it has not already been removed. If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted in “Removing the Unit” on page 3. 2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis. 18253Bend Tabs Screw Stud 3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. 4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. 5. Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors tape to ensure proper operation. 6. After completing the wiring turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the ignition switch off and proceed with final mounting of the chassis. 7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place. 8. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut and spring washer provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and plain washer provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight Dashboard Plain Washer Screw ( 5 x 25mm) Hex Nut (5mm) Spring Washer Screw Stud Support Strap of the radio or improper operation due to vibration. 9. Test radio operation by referring to the operating instructions for the unit. Removing the Unit To remove the radio after installation, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Reconnect the Battery When wiring is complete, reconnect the battery negative terminal. Removal Key 3 JCDWIN 4 WIRING 15A FUSE A - A Wire Connector A- A SHOWN FROM PIN VIEW ACCESSORY/IGNITION (+) Connect to existing radio accessory fuse or +12 VDC switched power source. POWER ANTENNA Connect to power antenna or amplifier. If not used, tape bare end of wire. MEMORY/BATTERY (+) GROUND Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected. Connect to ground terminal or clean, unpainted metal part of chassis. JCDWI N BASIC OPERATION 1 46 5 23 8 10 16 9 11 12 13 14 21 15 20 19 18 7 22 17 Power On/Off ( ) Press the button ( 1) to turn the unit ON or OFF. Volume Control To increase the volume, turn the AUDIO control (4) clockwise. To decrease the volume, turn the AUDIO control counter-clockwise. If using the remote control, press the VOL /\ or VOL \/ button ( 24) to adjust the volume. When the volume is adjusted, the volume level is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest). Mute Press the MUTE button (8) on the control panel (or the MUT button on the remote control) to mute the audio output. “ Mute” will appear on the display. Press MUTE again to restore the audio output to the previous level. Mode Press the MODE button (5) on the control panel (or the MOD button on the remote control) to select a different mode of operation, as indicated on the display panel. Available modes include ...
Dieses Handbuch ist für folgende Modelle:Player - JCDWIN (602.64 kb)