Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1. Remove the hard drive. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the hinge covers. 5. Remove the two M2 x 4-mm screws on the left side of the display panel and the two M2 x 4-mm screws on the right side of the display panel. NOTE: If you have a Hitachi display panel, remove the two M2 x 4-mm screws from the center of the left side of the display panel. 6. Remove the M2 x 4-mm screw that secures the display-feed flex cable to the display assembly through the black plastic flex-cable retention bracket (see "14.1-Inch Display Bezel and Panel"). 7. Lift from the top and rotate the display panel out of the top cover. 8. Disconnect the bottom flex cable connector from the inverter connector by pulling straight up on the attached pull tab (see "Display-Feed Flex Cable Connections"). Display-Feed Flex Cable Connections 1 display panel connector 2 top flex cable connector 3 pull tab 4 bottom flex cable connector 5 inverter connector 9. Remove the tape that secures the display panel connector and the tape that secures the middle of the display-feed flex cable to the display panel. 10. Pull the top flex cable connector down and away to remove it from the display panel connector. Replacing the 14.1-Inch Display Panel 1. Reconnect the top flex cable connector to the display panel connector. 2. Reconnect the bottom flex cable connector to the inverter connector. 3. Replace the tape that secures the display panel connector and the tape that secures the middle of the display-feed flex cable to the display panel. 4. Place the bottom edge of the display panel in the bottom of the top cover and elevate the top of the panel with your hand. 5. Lay the display panel in the top cover. 6. Reinstall the five M2 x 4-mm screws that secure the display panel to the top cover. Display Latch NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. Removing the Display Latch 1. Remove the hard drive. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the two M2.5 x 5-mm screws and the two M1.7 x 3.5-mm screws that secure the display latch and bracket to the top cover. 5. Lift the display latch and bracket up and out of the top cover. Display Latch Removal (14.1-Inch XGA Panel Shown) 1 M1.7 x 3.5-mm screws (2) 2 M2.5 x 5-mm screws (2) 3 display latch 4 bracket Replacing the Display Latch 1. On 14.1-inch XGA panels, place the display latch on top of its screw holes, and then place the bracket on top of the display latch, aligning the bracket and display latch screw holes. On 14.1-inch SXGA+ panels, align the screw holes and place the display latch and attached bracket in the top cover. 2. Replace the two M2.5 x 5-mm screws and the two M1.7 x 3.5-mm screws that secure the display latch and bracket to the top cover. Hinge Covers Removing the Hinge Covers 1. Remove the display assembly. 2. Rotate the hinges forward at an angle of approximately 90 degrees to the front of the display assembly. 3. To remove the hinge covers, slide them off the hinges. Hinge Cover Removal Replacing the Hinge Covers 1. Attach the display assembly to the bottom case. 2. Close the display assembly. 3. Snap the hinge covers in place over the hinges. NOTE: The right plastic hinge cover label includes an "R," and the left plastic hinge cover label includes an "L." The hinge cover labels face the back of the computer. Hinge Cover Replacement 1 right hinge cover 2 left hinge cover Back to Contents Page Back to Contents Page Palm Rest Dell™ Latitude™ C610/C510 Service Manual Removing the Palm Rest Removing the Palm Rest NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1. Remove the hard drive. 2. Remove the keyboard. NOTICE: You must remove the display assembly before you remove the palm rest; the display hinges pass through the back of the palm rest. 3. Remove the display assembly and hinge covers. 4. Turn the computer over and remove the three M2.5 x 12-mm screws labeled "circle P." Palm Rest Screw Removal 1 M2.5 x 12-mm screws (3) 2 M2 x 3-mm screws (2) 3 hard-drive bay door 5. Remove the two M2 x 3-mm screws that are located in the hard-drive bay door labeled "circle P." 6. Turn the computer over, and remove the three M2 x 3-mm screws that secure the palm rest to the bottom case. a. Remove the two M2 x 3-mm screws that ...