Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Open the back door. 2. Unscrew 3 screws and remove the Riser card bracket kit. 3. Secure 2 screws to fix the CD-ROM PCB board. Hardware Installation 13 PC 6170 User’s Manual 4. Put the CD-ROM in the drive bracket and fix it by 6 screws. 14 Hardware Installation PC 6170 User’s Manual 2.5 3 x Serial Ports The PC 6170 provides three onboard serial ports installed on the back bottom side of the chassis. For systems, COM1 and COM2 are RS- 232 and COM4 is RS-232/422/485. Each serial port is with +5V/+12V power capabilities on both Pin 1 and Pin 8, ready to accommodate a wide array of serial devices, such as fax modem, scanner, serial mouse and touch screen...etc. COM1 to COM4 are all D-SUB 9-pin connectors. To connect any serial devices, just plug in the device connector to the 9-pin D-SUB. In terms of transmission distance, the RS-422/485 will perform better than RS-232. In this case, COM4 is suggested to be set to RS-422/485 and the related jumpers have to be set correctly first (see the system board User’s Manual). The RS-422/485 pin assignment is listed as follows; Pi n # Sig n a l Na me R2 -422 RS -485 1 2 3 4 5 6 7 8 9 1 TX- D A TA - 2 N o co nn ec t o r No c o nn ect o r 3 TX+ D A TA+ 4 N o co nn ec t o r No c o nn ect o r 5 RX + No c o nn ect o r 6 N o co nn ec t o r No c o nn ect o r 7 RX - No c o nn ect o r 8 N o co nn ec t o r No c o nn ect o r 9 GN D G N D 10 N o co nn ec t o r No c o nn ect o r 2.6 Parallel Port The printer interface is a 25-pin D-SUB connector. To connect any parallel device, just plug in the device connector to the 25-pin D-SUB. 2.7 VGA The PC 6170 has an analog RGB interface connector. It is able to connect to an expansion CRT monitor, and the system can display on both the flat panel and the CRT simultaneously. 16 Hardware Installation PC 6170 User’s Manual 2.8 Ethernet The PC 6170 provides an NE2000 compatible Ethernet (RJ-45) interface. For network connection, just plug in one cable end of the PC 6170 10/100/1000-Base-T Hub into the standard RJ-45 connector. The pin assignment of the RJ-45 is listed below; R J - 4 5 C o n n e c to r Pin A ssignme nt Pi n Signa l 1 TX+ (Data tr an smission positive 2 TX- (Data transmission negative) 3 Rx +(Da ta reception positive) 4 RJ 45 te rm ination 5 RJ 45 te rm ination 6 Rx - (Data reception negative) 7 RJ 45 te rm ination 8 RJ 45 te rm ination 1 2 3 4 5 6 7 8 RJ-45 Hardware Installation 17 PC 6170 User’s Manual 2.9 Mountings: Panel/Wall/Desktop/VESA/Rack There are 5 application options for the PC 6170, Panel/Wall/Desktop/VESA/Rack mountings. 2.9.1 VESA-ARM The PC 6170 provides two ways for VESA mount: 75x75 mm and 100x100 mm. Screw four screws to fix the kit (included in the package) in the back chassis. 18 Hardware Installation PC 6170 User’s Manual 2.9.2 Wall Mount The PC 6170 is designed for Wall mount application. To mount the PC 6170, the standard set of mounting kit (included in the system packaging) is needed. Please refer to the following figure. 1. Fix VESA bracket kit in back of chassis by 4 screws. Hardware Installation 19 PC 6170 User’s Manual 2. Fix the Wall mount bracket kit in back of the VESA bracket kit by 4 screws. 20 Hardware Installation PC 6170 User’s Manual 2.9.3 Desktop Kit Assembly The PC 6170 is designed for desktop application. The standard set of desktop kit is included in the system packaging. Please refer to the following figure. 1. Fix VESA bracket kit in back of chassis by 4 screws. 2. Fix the Wall mount bracket kit in back of the VESA bracket kit. Hardware Installation 21 PC 6170 User’s Manual 3. Fix two holders by 2 screws. 4. Complete. 22 Hardware Installation PC 6170 User’s Manual 2.9.4 Panel-mount Kit Assembly The PC 6170 is designed for panel mount application. To mount the PC 6170, the standard set of mounting kit (included in the system packaging) is needed. Hardware Installation 23 PC 6170 User’s Manual 2.9.5 Rack mounting Assembly The PC 6170 is designed for rack mounting application. Remove plugs from front panel. Then, user could mount PC 6170 at their rack. remove remove remove remove 24 Hardware Installation PC 6170 User’s Manual C h a p t e r 3 Driver Installation 3.1 System PC 6170 could support with Windows 95, Windows 98 or Windows 2000/XP. To facilitate installation system driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Insert Driver CD and select the \P1170-810\Driver\.. 2. Select all files and follow the install procedure and press OK. Driver Installation 25 PC 6170 User’s Manual 3.2 Touch Screen 3.2.1 Specification To u c h S c r e e n : For 8-wire analog resistive type T o uc h S c r e en C o nt r o l l er : DMC9000 Co mm u n i c a t io ns : RS-232 Ba ud R a te : 19200 baud rate fixed Re s o lu tion: 1024 x 1024 (10-bit A/D converter inside) Po w e r I n p u t : 5V to 12V DC Po w e r Co n s um pt i o n : 12V: 27mA+ i where (i = v/touch screen sheet R) 5V: 23mA+ i where (i = v/touch screen sheet R) Bo ard Si ze : 6.0 x 2.0 cm Po r t...