Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung John Deere, modell PR2-8GM

Hersteller: John Deere
Dateigröße: 2.96 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Insufficient pressure at air tool or accessory. Pressure Regulator not turned to high enough pressure or defective. Restricted air intake . Air leaks or restrictions. Hose or hose connections are too small or long. Slipping belt. Air compressor is not large enough for air requirement. Restriction in Pilot Valve. Adjust Pressure Regulator to proper setting or replace. Clean or replace Air Intake Filter. Check for leaks and repair. Replace with larger hose or connectors. Tighten or replace. Check the accessory air requirement. If it is higher than the CFM or pressure supply to the air compressor, use a larger air compressor. Clean or replace. Air leaks from Safety Relief Valve Possible defective Safety Relief Valve. Excessive air tank pressure. Operate Safety Relief Valve manually by pulling on ring. If it still leaks, it should be replaced. Clean, reset or replace Pilot Valve. TROUBLESHOOTING SYMPTOM PROBABLE CAUSE REMEDY Air leaks at pump. Defective gaskets. Torque head bolts: Single Stage= 17 ft./lbs. Two Stage= 33 ft./lbs. Air blowing from Air Intake Filter. Defective inlet (reed) valve. Contact your Customer Service. Condensation in air tank caused by high level of atmospheric humidity or air compressor is not run long enough. Moisture in discharge air. Run air compressor a minimum of one hour to prevent condensation buildup. Drain air tank after every use. Drain air tank more often in humid weather and use an air line filter. Excessive oil consumption or oil in hose. Clean or replace. Do not incline the air compressor more than 10° in any direction while running. Drain oil. Refill to proper level with SAE-30W non-detergent oil. Drain oil. Refill to proper level with SAE-30W non-detergent oil. Clean. Clean or replace. Torque head bolts: Single Stage= 17 ft./lbs. Two Stage= 33 ft./lbs. Contact your Customer Service. Restricted Air Intake Filter. Air compressor on unlevel surface. Crankcase overfilled with oil. Wrong viscosity. Plugged oil dipstick vent. Plugged crankcase breather. Oil leaks. Worn piston rings or scored cylinder. Oil has milky appearance. Water in oil due to condensation. Change oil and move air compressor to a less humid environment. NOTES STATEMENT OF WARRANTY John Deere warrants all parts, (except those referred to below), of your new air compressor to be free from defects in materials and workmanship during the following periods: For One (1) year from the date of original purchase: Compressor Pump Plumbing Tank Assembly For Six (6) months from date of original purchase: Pressure Switch Regulator Check Valve Pilot Valve Copper/stainless steel line For Ninety (90) days from the date of original purchase: Pressure Gauges Safety Relief Valves Drain Valves Defective parts not subject to normal wear and tear will be repaired or replaced at our option during the warranty period. In any event, reimbursement is limited to the purchase price paid. EXCLUSIONS 1. Engine is covered under separate warranty by its respective manufacturer and is subject to the terms set forth therein. 2. Normal wear parts: Isolators Air Filter 3. This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, accidents, operation at other than recommended speeds, pressures or temperature, improper storage or freight damage. Parts damaged or worn by operation in dusty environments are not warranted. Failure to follow recommended operating and maintenance procedures also voids warranty. 4. Labor charges, loss or damage resulting from improper operation, maintenance (other than routine air tank draining and oil changes, if applicable) or repairs made by persons other than an Authorized Service Center. 5. The use of other than Genuine Repair Parts will void warranty. Parts returned, prepaid to our factory or to an Authorized Service Center will be inspected and replaced free of charge if found to be defective and subject to warranty. Under no circumstances shall the manufacturer bear any responsibility for loss of use of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages. There are no warranties which extend beyond the description of the face hereof. For Service or Warranty consideration, contact: Mi-T-M Corporation, 8650 Enterprise Drive, Peosta, IA 52068-0050 1-877-JD KLEEN / (1-877-535-5336 / Fax 563-556-1235 Monday-Friday 8:00 a.m. - 5:00 p.m. CST 20 Manuel ...