Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Campbell Hausfeld Dateigröße: 2.53 mb Dateiname: Unterrichtssprache:

Air pressure should escape. When the ring is released, it will reset. MOTOR/PRESSURE SWITCH: This switch is used to start or stop the air compressor. Moving the switch to the "Auto" (On) position will provide automatic power to the pressure switch which will allow the motor to start when the air tank pressure is below the factory set "cut-in" pressure. When in the Start/Stop Option, the pressure switch stops the motor when the air tank pressure reaches the factor set "cut-out" pressure. For safety purposes, this switch also has a pressure release valve located on the side of the switch designed to automatically release compressed air from the air compressor pump head and its discharge line when the air compressor reaches "cut-out" pressure or is shut off. This allows the motor to restart freely. Moving the switch to the "Off" position will remove power from the pressure switch and stop the air compressor. AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the knob counterclockwise. MOTOR THERMAL OVERLOAD: The electric motor has a manual thermal overload protector. If the motor overheats for any reason, the thermal overload will cut off power, thus preventing the motor from being damaged. Wait until the motor is cool before pressing the thermal overload button to reset and begin working again. OIL FILL PORT/VENT: Pour oil into the Oil Fill Port/Vent when required. OIL SIGHT GLASS: The Oil Sight Glass displays the oil level in the pump. The oil level should be at the center of the Oil Sight Glass. If low, add SAE 30W non-detergent oil. PILOT VALVE OPTION: When the adjusting knob is turned completely clockwise to the fully closed position, the air compressor operates in the Start/Stop position. When the adjusting knob is turned completely counterclockwise to the fully open position, the air compressor operates in the constant run position. WARNING THE FOLLOWING PAGES CONTAIN OPERATING AND MAINTENANCE INSTRUCTIONS. DO NOT ATTEMPT TO OPERATE THIS AIR COMPRESSOR UNTIL YOU HAVE READ AND UNDERSTOOD ALL SAFETY PRECAUTIONS AND INSTRUCTIONS LISTED IN THIS MANUAL. INCORRECT OPERATION OF THIS UNIT CAN CAUSE SERIOUS INJURY!! DO NOT ALTER OR MODIFY THIS EQUIPMENT IN ANY MANNER! Portable Electric Air Compressor Manual WARNING PREPARATION INSTRUCTIONS RISK OF EXPLOSION OR FIRE CAUSING SERIOUS INJURY OR DEATH! Do not allow the motor or Motor/ Pressure Switch to come in contact with flammable vapors, combustible dust, gases or other combustiblematerials. Anelectric spark may cause an explosion or fire. When using the air compressor for spray painting, place the air compressor as far away from the workareaaspossible,usingextra air hoses instead of extension cords. INITIAL SET-UP: 1. Read safety warnings before setting-up air compressor. 2. Ensure the oil level in the air compressor pump is adequate. If low, add SAE-30W non-detergent oil. LOCATION: 1. In order to avoid damaging the air compressor, do not incline the aircompressor transversely or longitudinally more than 10°. 2. Place air compressor at least 12 inches away from obstacles that mayprevent proper ventilation. Do not place air compressor in an area: -where there is evidence of oil or gas leaks. -where flammable gas vapors or materials may be present. -where air temperatures fall below 32°F or exceed 104°F. -where extremely dirty air or water could be drawn into the air compressor. ELECTRICAL: 1. USE OF AN EXTENSION CORD IS NOT RECOMMENDED because it could cause the compressor motor to overheat. It's preferable to use additional air hose instead of an extension cord. 2. If use of an extension cord is unavoidable, be sure to use one heavy enough to carry the current your compressor will draw. Minimum cord sizes is as follows: Cord Length Wire Gauge Up to 25 Feet 12 AWG 26 to 100 Feet 10 AWG 101 to 150 Feet 8 AWG 151 to 250 Feet 6 AWG 3. Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the compressor. 4. Examine cords before using. Do not use the compressor if its cord is damages. Do not use a damaged extension cord. 5. Keep cords away from heat and sharp edges. Do not pull on a cord to disconnect a plug -- grasp the plug. 6. Always shut off the compressor Pressure Switch before unplugging the compressor. PRE-START CHECKLIST: 1. Check oil level. Add if necessary. 2. Remove any moisture in the air compressor air tank. NEVER attemptto open the Air Tank Drain Valve when more than 10 PSI of air pressure is in the air tank! Remove excessive pressure with an air tool, then open the Air Tank Drain Valve in the bottom of the air tank. Close tightly when drained. 3. Make sure the Motor/Pressure Switch is in the "OFF" position. 4. Make sure the Safety Relief Valve is working correctly. 5. Make sure all guards and ...

Herunterladen

Geben Sie zwei Ziffern: