Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Campbell Hausfeld Dateigröße: 1.72 mb Dateiname: Unterrichtssprache:

Do not modify plug provided; if it will not fit outlet, have proper outlet installed by a qualified electrician. Overheating, short circuiting and fire damage will result from inadequate wiring, etc. Operation Definition of Terms Regulator - The regulator controls the amount of air pressure released at the hose outlet. ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset maximum. Handle - Designed to move the compressor. Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the tank daily to reduce the risk of corrosion. Reduce tank pressure below 10 psi, then drain moisture from tank daily to avoid tank corrosion. Drain moisture from tank by opening the drain valve located underneath the tank. ! CAUTION ! WARNING ! DANGER LUBRICATION This is an oilless product and DOES NOT require lubrication to operate. BEFORE FIRST START-UP BREAK-IN PROCEDURE (Complete this procedure before using compressor for the first time. Once completed, it is not necessary to repeat.) 1. Turn regulator knob fully clockwise (to the right) to open air flow. 2. Turn on/off switch to OFF position. 3. Plug in power cord. 4. Turn on/off switch to ON position and run compressor for 5 minutes. 5. Turn on/off switch to OFF position. 6. Unplug power cord. The compressor is now ready for use. BEFORE EACH START-UP OPERATING PROCEDURE 1. Turn regulator knob fully counterclockwise (to the left) to close air flow. 2. Connect air hose to outlet of regulator. 3. Turn on/off switch to OFF position. 4. Plug in power cord. 5. Turn on/off switch to ON position and let compressor run until it reaches automatic shutoff pressure. 6. Attach tire chuck or tool to end of hose. 7. Turn regulator knob clockwise (to the right) to desired pressure of tool being used. On/Off cycling of compressor In the ON position, the compressor pumps air into the tank. When a shutoff (preset “cut-out”) pressure is reached, the compressor automatically shuts off. 22 Sp Compresores Sin Aceite Handle Regulator ON/OFF Switch Drain Valve Figure 2 - Unit Identification Safety Valve Guia de diagnostico de averias (Continuacion) Problema Posible(s) Causa(s) Accion a tomar 1. Demasiada agua en el tanque 2. Humedad elevada 1. Presostato defectuoso 2. Valvula de seguridad defectuosa 1. Demasiada condensacion en el tanque 2. Conexiones flojas (accesorios, tuberia, etc.) 1. Drene el tanque, incline el tanque para eliminar la humedad 2. Llevelo a un area menos humeda, utilice un filtro de aire de linea Nota: La condensacion de agua no es una causa para el malfuncionamiento del compresor. 1. Cambie el interruptor de presion 2. Cambie la valvula de retencion con un repuesto original 1. Drene con mas frecuencia 2. Revise todas las conexiones con una solucion de agua y jabon. Si se detecta una fuga, apriete. O quite la conexion y aplique cinta para tuberias a las rocas y vuelva a armar. Exceso de humedad en el aire de descarga El compresor funciona en forma continua y la valvula de seguridad se abre cuando aumenta la presion Arranques y paradas excesivas Gauge of Cord 18 18 16 14 14 12 12 10 10 Extension cords for 120V/2.5 Amp Unit Length of Cord (ft) 25 50 100 150 200 250 300 400 500 Oilless Compressors Operation (Continued) If the compressor is left in the ON position and air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically at its preset “cut-in” pressure. When a tool is being used continuously, the compressor will cycle on and off automatically. In the OFF position, the pressure switch cannot function and the compressor will not operate. Make sure switch is in OFF position when connecting or disconnecting po...

Herunterladen

Geben Sie zwei Ziffern: