Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Franklin
Dateigröße: 135.19 kb
Dateiname: 5054d11a-4839-459e-a752-2e55f47b7f32.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
INSPECTION Examine the equipment when received. Notify your dealer or carrier of any damage or missing parts. Verify that the equipment is of size and model specified. READ AND FOLLOW SAFETY INSTRUCTIONS This is the safety alert symbol. When you see this symbol on your pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury: DANGER warns about hazards that will cause serious personal injury, death or major property damage if ignored. WARNING warns about hazards that can cause serious personal injury, death or major property damage if ignored. CAUTION warns about hazards that will or can cause minor personal injury or major property damage if ignored. The label NOTICE indicates special instructions, which are important but not related to hazards. Carefully read and follow all WARNING safety instructions in this manual and on pump. Keep safety labels in good condition. Replace missing or damaged safety labels. Hazardous voltage. Can shock, burn, or cause death. Wire motor for correct Ground pump before voltage. See “Electrical” connecting to power section of this manual and supply. Disconnect motor nameplate. power before working on pump, motor Ground motor before or tank. connecting to power supply. Meet National Electrical Code, Canadian Electrical Code, and local codes for all wiring. Follow wiring instructions in this manual when connecting motor to power lines. INSTALLATION LOCATION All S & J Series pumps are designed for fl ooded suction (all suction fittings and suction piping are below water level) and will not self-prime. GENERAL PLUMBING FOR SOLVENT WELD CONNECTIONS Rigid or flexible PVC pipe can be used. Pipe ends should be clean and free of any flash caused by the cutting operation. Be sure that the proper adhesive is used on the type of pipe specified. Recommended Adhesives- These are examples only and are not intended to restrict brands. PVC-PVC JOINT PVC-ABS JOINT Uni-weld Pool-Tite 2000 Uni-weld Pool-Tite 2000 Suregard Flex 20 Suregard Weld-all No. 5 IPS Weld-on 705 IPS Weld-on 794 NOTE: A Primer will assure that adhesives joints are superior. Sureguard P-3000 has a purple tracer to qualify in areas where codes specify a primer must be used. CAUTION-We recommend that you consider climatic conditions when applying adhesives. Certain atmospheric situations, such as high moisture content, make the adhesive action of certain glues less effective. Check the manufacturer’s instructions. FOR THREADED CONNECTIONS Use only Teflon tape or equivalent on threaded plumbing connections. Other pipe compounds may damage threads. We do not recommend the use of silicone or petroleum based compounds. DO NOT OVER TIGHTEN! HAND TIGHTEN PLUS 1/2 TURN IS SUFFICIENT. PUMP PLUMBING All S & J Series pumps are union connected allowing quick and easy service without disturbing the plumbing. Two different plumbing configurations are available offering 1-1/2” suction connection and either 1-1/2” discharge or 1” tee discharge. These union packages must be ordered separately. Avoid using a suction pipe smaller than pump connection. To maximize the 100% drain feature, keep the piping as straight and short as possible, and slope horizontal runs so water drains away from pump. The suction line must be installed at an elevation below the water level when the tub is filled to guarantee fl ooded suction. ELECTRICAL DATA Refer to information on motor nameplate for electrical service data. All motors should have fused disconnect switch or circuit breaker. Be sure wire size is sufficient for HP and distance from power source. Wiring should be done in accordance with applicable codes by competent electrician. We recommend the installation of a ground fault circuit interrupter for maximum safety. PUMP START UP Fill tub to desired level making sure that suction fittings and jets are below water level. Start pump and open all suction and discharge line valves. After about 10 minutes of operation, check the return fittings for air bubbles. A continuous flow of air indicates leaks in the suction line. Locate and correct any leaks immediately. CAUTION- Do not operate pump with closed suction or discharge valves. TWO-SPEED PUMPS Two-speed models are recommended in a swimming pool when high speed is needed for maximum filtration at peak periods and whenever turbidity levels are high. At other times, switch to low speed. For backwashing and vacuuming, high speed is required. In spa and hot tubs, use high speed to atain full performance in the hydro-therapy mode. At other times, such as filter/heat cycle mode, use low speed. Low speed provides sufficient flow to activate most spa heaters and provides sufficient fl ow for filtration. In jetted tubs, use high speed to attain full performance in the hydro-therapy mode and use low speed for desired low fl ow conditions. NOTE: Two-speed pumps must be in high speed mode to prime. PUMP MAINTENANCE 1. Motors are self-lubricating-- no lubricat...