Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
8. Apply sealant to the check valve threads. Reinstall the check valve (turn clockwise). 9. Replace the pressure release tube. Tighten nuts. 10. Replace the outlet tube and tighten nuts. 11. Perform the Break-in Procedure. See “Break-in Procedure” in the Operation section. D26161 20-ENG Motor This motor has a manual thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. To restart: 1. Place the On/Auto/Off lever in the Off position. 2. Allow the motor to cool. 3. Depress the red reset button on the motor. Reset Button 4. Place the On/Auto/Off lever in the On/Auto postion to restart the motor. IMPORTANT: If the overload protector shuts the motor off frequently, check for a possible voltage problem. Low voltage can also be suspected when: 1. The motor does not get up to full power or speed. 2. Fuses blow out when starting the motor; lights dim and remain dim when motor is started and is running. Additional Service Disassembly or service of the air compressor beyond what is covered in this manual is not recommended. If additional service is required, contact your nearest Authorized Warranty Service Center. STORAGE Before you store the air compressor, make sure you do the following: 1. Review the “Maintenance” section on the preceding pages and perform scheduled maintenance as necessary. 2. Set the On/Auto/Off lever to “OFF”. 3. Close the globe valve. 4. Remove the air tool or accessory. 5. Open the globe valve and allow the air to slowly bleed from the air tank until tank pressure is approximately 20 psi. 6. Drain water from air tank by opening drain valve (counterclockwise) on bottom of tank. Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture. 7. After the water has been drained, close the drain or drain valve. NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled. 8. Protect the air hose from damage (such as being stepped on or run over). 21-ENG D26161 TROUBLESHOOTING Performing repairs may expose voltage sources, moving parts or compressed air sources, moving parts or compressd air sources. Personal injury may occur. Prior to attempting any repairs, unplug the air compressor and bleed off all air tank air pressure. PROBLEM CAUSE CORRECTION Excessive tank Pressure switch does not Move On/Auto/Off lever to pressure shut off motor when comthe “OFF” position, if the (safety valve) pressor reaches “cut-out” outfit does not shut off pops off. pressure. Pressure switch “cut-out” too high. contact a Trained Service Technician. Contact a Trained Service Technician. Air leaks at Tube fittings are not tight Tighten fittings where air can fittings. enough. be heard escaping. Check fittings with soapy water solution. DO NOT OVERTIGHTEN. Air leaks at or Check valve seat damaged. A defective check valve inside check results in a constant air leak valve at the pressure release valve when there is pressure in the tank and the compressor is shut off. Replace check valve. Refer the “To Replace or Clean Check Valve” in the “Operation” section. Air leaks at pressure switch release valve. (if equipped) Defective pressure switch release valve. Contact a Trained Service Technician. Air leaks in air tank or at air tank welds. Defective air tank. Air tank must be replaced. Do not repair the leak. Do not drill into, weld or otherwise modify air tank or it will weaken. The tank can rupture or explode. Air leaks between head and valve plate. Leaking seal. Contact a Trained Service Technician. D26161 22-ENG PROBLEM CAUSE CORRECTION Pressure reading It is normal for “some” If there is an excessive amount on the regulated pressure drop to occur. of pressure drop when the pressure gauge accessory is used, adjust the (if equipped) regulator as instructed in the drops when an Operation section. accessory is NOTE: Adjust the regulated used. pressure under flow conditions (while accesory is being used). Air leak from safety valve. Possible defect in safety valve. Operate safety valve manually by pulling on ring. If valve still leaks, it should be replaced. Compressor is Prolonged excessive use of Decrease amount of air usage. not supplying air. enough air to Compressor is not large Check the accessory air operate accesenough for air requirement. requirement. If it is higher than sories. Hole in hose. Check valve restricted. Air leaks. Restricted air intake filter Loose belt the SCFM or pressure supplied by your air compressor, you need a larger compressor. Check and replace if required. Remove and clean, or replace. Tighten fittings. Clean or replace air intake filter. Do not operate the air compressor with the filter removed. Refer to the “Air Filter” paragraph in the “Maintenance “ section. Check belt tension, see Adjusting Belt Tension in the Maintenance section Restricted air intake D...