Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The pump is made up of two basics sub-assemblies. They are the Wet End Assembly (Items 1-10); and the Drive Magnet, Bracket and Motor Assembly (Items 11-15). To separate the 2 assemblies, simply remove the 4 round head screws (Item 1). The pump will then separate into the 2 sub-assemblies. The water will still be contained within the Wet End assembly unless you loosen the screws (Item 10) on the rear of the Wet End assembly. LUBRICATION: The motor should be oiled at least once a year at the start of the heating season with 4 or 5 drops of SAE 20 weight non-detergent oil in each bearing. If the pump is used year around it should be oiled every six months. Do not over oil. No oiling is required on the ball bearing motors. GENERAL SAFETY INFORMATION: Follow all local electrical and safety codes, and the Occupational Safety and Health Act (OSHA). Make certain that the power source conforms to the requirements of your equipment. Always disconnect power source before performing any work on or near the electric motor. Caution must be exercised to relieve any pressure in the system and in draining hot water from the pump or the system. DISASSEMBLY AND REASSEMBLY: 1—The motor assembly (Item 15) can be removed from the Wet End assembly without having to drain the liquid out of the system. 2—Remove four screws (Item 1) and slide the motor assembly away from the Wet End assembly. 3—If you must replace parts inside the pump housing assembly, then first close off the valves that supply water to the heating system or to the hot water tank. Drain the system to relieve any pressure. 4—After the system is drained and cool enough to handle, then remove the four screws (Item 10) on the rear of the housing. 5—The impeller magnet housing (Item 9) can now be removed. It may be snug fit into the pump housing and it may be necessary to pry evenly, under the four ears to loosen it. 6—Remaining pump parts can now be lifted out in sequence as shown on the exploded view. Replace any worn or damaged parts. Replace the “O” ring (Item 3) anytime the impeller magnet housing is removed. Note: Pumps with 12 and 24 volt motors are available. Contact the factory for more information. REPAIR PARTS LIST ITEM DESCRIPTION QTY. PART NO. 1 #8 x 1-1/4 Long Rd. Hd. Screw 4 0923-0003-1000 2a Pump Housing w/.” MPT 1 0809-0013-0000 2b Pump Housing w/Center Inlet Style* 1 0809-0142-0000 2c Pump Housing Plastic w/.” MPT* 1 0809-0079-1000 3a “O” Ring, Silicon Rubber, used in bronze housing (2a & b) 1 0809-0165-1000 3b “O” Ring, Silicon Rubber, used in plastic housing (2c) 1 0809-0027-1000 4a Impeller Shaft w/Thread 1 0809-0008-1000 4b Impeller Shaft w/”D” Flat 1 0809-0161-1000 5 Thrust Washer 1 0809-0043-1000 6 Impeller & Magnet Assembly 1-11/16 Dia. (3400 RPM) 809 HS 1 0809-0005-0200 7 Impeller & Magnet Assembly 2 Dia. (1600 RPM) 809 1 0809-0005-0100 8 Impeller & Magnet Assembly 2-5/32 Dia. (3400 RPM) 815 1 0809-0107-0200 9 Impeller Magnet Housing 1 0809-0012-1000 10 #8 x 3/8 Long Rd. Hd. Screw ...
Dieses Handbuch ist für folgende Modelle:Pumps - Water Pump (69.04 kb)
Pumps - Water Pump (69.04 kb)