Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
After the first 10 hours of working, empty the crank case of oil and refill with clean oil by removing the crank case oil plug (left hand side of the crank case at the bottom) NOTE. Use good quality compressor lubricating oil. • SAE30 or L-DAB 100 over 10°C • SAE10 or L-DAB 68 under 10°C 2. After each subsequent 500 hours of operation, again drain the oil and refill the crank case with clean oil. 3. After each day of operation, use the drain cock (11) under the tank to drain off any condensate. 4. Regularly check the air filter cartridge inside the air filter assembly (17) and replace the cartridge when necessary. 14 AC30G_AC40G 14 12/8/05, 4:49 PM 5. Check daily the operation of the safety valve. This check should be performed when the tank contains close to max pressure in the tank. To check the valve, pressurise the tank, and pull the ring OUTWARDS on the safety valve. Air should discharge from the valve. Release the ring of the safety valve. When the ring is released the air discharge must stop. WARNINGS. Safety glasses must be worn when performing this test. Do not have your face close to the safety valve when performing this test as air will discharge from the valve at a high force. If the safety valve does not operate correctly in any way as described above, turn off the compressor immediately and have the compressor and safety valve checked and tested at an authorised Service centre. DO NOT CONTINUE TO USE THE COMPRESSOR IN ANY WAY IF THE SAFETY VALVE DOES NOT WORK AS ABOVE. General inspection 1. Regularly check that all the fixing screws are tight. 2. The supply cord of the tool should be checked frequently for damage. If damaged, have the cordset replaced by an authorised service facility to avoid a hazard. Cleaning 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a soft brush or a rag. 3. Re-lubricate all moving parts at regular intervals. 4. If the body of the compressor needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but nothing like alcohol, petrol or other cleaning agent. 5. Never use caustic agents to clean plastic parts. Caution. Water must never come into contact with the tool Power cord maintenance Only an authorised service centre should replace the cordset or carry out other repairs. If the cordset is damaged or worn, have it repaired or replaced by an authorised service centre. 15 AC30G_AC40G 15 12/8/05, 4:49 PM Carefully read the entire Instruction Manual before using this product. With continuing product development changes may Before returning this product for a have occurred which render the product received Warranty Claim or any other reason slightly different to that shown in this instruction Please Call 1300 880 001 (Australia) manual. The manufacturer reserves the right to or 0800 445 721 (New Zealand) change specifications without notice. Note: Specifications may differ from country to country. When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer will take your call and, in most cases, will be able to solve your problem over The GMC 777 Helpline operates from 7am to the phone. 7pm, 7 days a week (EST). This allows you You are welcome to use this phone-in service to to contact GMC directly with any queries and make suggestions or give comments about any technical questions you have regarding GMC product. our products. 45–55SouthCentreRoadMelbourneAirport Victoria, Australia 3045 Tel: (03) 8346 1100 Fax: (03) 8346 1200 Save this Manual for future reference. AC30G_AC40G 16 12/8/05, 4:49 PM ...
Dieses Handbuch ist für folgende Modelle:Pumps - AC40G (444.39 kb)