In the positive range, the envelope is a decay-type envelope. Adjusts the level of the effect sound mixed to the original sound. mdMD MULTI TAP DELAY This effect produces several delay components with different delay times. TIME 1 – 99, 1.0 – 5.0 PATTERN 1 – 8 MIX 0 – 98, 1.0 Adjusts the delay time. In the range from 10 – 990 ms, the adjustment is made in 10-ms steps (1 – 99). For 1 second and above, the adjustment is made in 100-ms steps (1.0 – 5.0). TAP Selects the combination pattern for the

If only one or two of the fine tuners are out of range you may want to try adjusting them without engaging the tremolo stop. Step 1: The first thing you do to reset the range of all the fine tuners is to position all the fine tuner screws to the middle of their possible movement. Step 2: One way to do this is to turn the low "low E" string fine tuner screw all the way up, then turn the "D" string fine tuner screw all the way down. Now, position the "A" string fine tuner screw half way between th

If the base plate appears to be tilted forward away from the top surface of the guitar or tilted back closer to the top of the guitar, then an adjustment should be made. Step 1: To level the base plate, first take the spring cover plate off the back of the guitar. Step 2: Inside the spring cavity you should find a tremolo stop. 10 Step 4: Now remove the bullet from the saddle. Step 5: If you are replacing a broken string, when you unlatch the pivoting saddle there will be no tension on the strin

Pluck the string you want to tune (Typically the "A" string for this procedure) and then, while watching the tuner, loosen first one claw screw then the other claw screw the same amount. Check the tuning and repeat until the string is in tune.When you get the string you chose in tune the other strings will be in tune.This assumes that all the strings were in tune before you released the tremolo stop. For foreign language translation of this owner's manual, please visit 15 tuning using the range

You should now have all of the fine tuner screws set to the middle of their range. Ignore the fact that your guitar is now completely out of tune, we're going to fix that next. At this point you're ready to tune your guitar using the range tuner set screw. You can set your guitar up for standard pitch, any open tuning, or any drop 13 Step 6: Now check the base plate position. If it is not parallel to the face of the guitar body turn the setscrew until the base plate is parallel. Step 7: After yo

Hughes & Kettner, zenAmp, DSM, Dynamic Sector Modeling, Z-Board, FS-5, the Hughes & Kettner logo, the zenAmp logo, the DSM Logo, Montana, WARP 7, and ATS 112 are trademarks or registered trademarks of Hughes & Kettner. All other product names are the property of their respective owners. TABLE OF CONTENTS 1.0 QUICK START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.0 AMP MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 3

Tanto el firmware como las instrucciones se pueden descargar del sitio web de Yamaha. - Si actualiza el firmware en la red por medio de YWA-10, conecte el cable de alimentación USB suministrado al puerto USB en el panel frontal del receptor. El terminal DC OUT del panel trasero no está diseñado para actualizaciones del firmware. Es posible que no se pueda actualizar el firmware dependiendo de las condiciones de la red inalámbrica. Lista de modelos de receptor AV: - RX-A3020, RX-A2020, RX-A10

Микропрограмму и инструкции можно загрузить с веб-сайта Yamaha по адресу - При обновлении микропрограммы по сети с помощью YWA-10 подключите входящий в комплект USB-кабель питания к USB-порту на передней пан

Die Firmware und die Anweisungen können von der Website von Yamaha heruntergeladen werden: - Wenn Sie die Firmware über das Netzwerk mit Hilfe des YWA-10 aktualisieren, schließen Sie das mitgelieferte USB-Netzkabel am USB-Port an der Vorderseite des Receivers an. Der DC-OUT-Anschluss an der Rückseite ist nicht für die Firmware-Aktualisierung vorgesehen. Je nach den Bedingungen des Drahtlosnetzwerks ist es evtl. nicht möglich, die Firmware zu aktualisieren. Liste der AV-Receiver-Modelle: - RX

Compatible devices can connect to the YWA-10 • Check that the Wireless LAN router (base unit) through a USB connector instead of a DC OUT jack. can connect to the Internet. Refer to the website below for a list of compatible © 2012 Yamaha Corporation Printed in China devices. To assure the finest performance, please read this AV Receiver Connecting to the base unit manual carefully. Keep it in a safe place for future reference. Package contents • When the Wireless LAN router (base unit) has a WP