By following these simple steps you’ll be set up and playing in no time! Be sure to look over the Drum Contents page and identify the parts and hardware that you’ll be using to assemble the drum set. Clear an area large enough to unpack the drums from the box and place the components of the set within reach. Make sure to leave a space where you can assemble the drum set.You’ll need the drum tuning key to complete set up and tuning. After set up, use the Drum Tuning Diagrams and Instructions belo

If the cable needs repair, do not plug the amplifier in. Have the amplifier repaired immediately by a qualified service technician. 5. Unplug your amplifier when not in use for extended periods of time. 6. Turn amplifier power off when not in use. 7. The outside of the amplifier may be cleaned with a dry cloth only. Do not use water or chemicals to clean. 8. This unit contains digital circuitry and may cause interference if placed too close to radio or television receivers. 9. Do not operat

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: 4 watts RMS Frequency Range: 60 Hz ~ 6 kHz Speaker: 4.5" / 8W / 4 ohms Input Sensitivity: 26 mV Power Supply:

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: 4 watts RMS Frequency Range: 60 Hz ~ 6 kHz Speaker: 4" / 8W / 4 ohms Input Sensitivity: 26 mV Power Supply: 14

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: Power Supply: 4 watts RMS 14V DC 500mA Frequency Range: Dimensions: (LxWxH) 60 Hz ~ 6 kHz 8" x 3.25" x 7.5" S

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT A power adaptor is NOT included. As an alternative to two 9V batteries, it is possible to power this amp with an adaptor. IMPORTANT - use only a 14V, 500mA adaptor with this amplifier (sold separately). INSTALLING BATTERIES The MA003 Amplifier opera

ALL RIGHTS RESERVED 7 PIECE DRUM SET DRUMS [A] 12” Snare Drum [B] 10” Tom Drum [C] 13” Floor Tom Drum [D] 18” Bass Drum CYMBALS [E] 12” Hi-hat Cymbals (2) [F] 14” Crash Cymbal STANDS / HARDWARE / DRUM HEADS [G] Snare Stand [H] Hi-hat Stand [I] Cymbal Stand [J] Bass Drum Pedal w/ Felt Beater [K] Tom Tom Mounting Arm w/ Memory Clamp [L] Bass Drum Spurs (2) [L.1] Retractable Rubber w/ Spiked Tip [M] Floor Tom Legs (3) [N] Bass Drum Tension Rods w/ Washers (12) [O] Bass Drum Rim Claws (12) [P] Bass

12346785 Important Safety Instructions Please read this section carefully. 1. Read and follow these instructions. 2. Do not use this device near water. 3. Clean only with a dry cloth. 4. Do not use near any heat sources such as radiators, heaters, or stoves. 5. Only use the attachments/accessories specified by the manufacturer. 6. Refer all servicing to qualified service personnel. Servicing is required when the drum pad has been damaged in any way, liquid has been spilled onto the drum pad, the

Open the door and refer to the image inside to install the batteries. Be sure to install negative (-) and positive (+) ends of the battery correctly. Incorrect installation can damage the drum pad or cause electrical hazard. Close the compartment door and tighten the screw. Note: If the batteries start to wear out, the drum pad's sound may deteriorate. If this happens, install a new set of batteries. If you are not going to play for a long time, remove the batteries from the drum pad. Do not m

Intended for use as a seat only. Do not stand. Bass Drum Assembly Place the bass drum shell (A) flat on the floor and place the drum head (R) on top. Rotate bass drum head so that the First Act logo is upright. Two spur insets will be on the bottom. Place bass drum hoop (Q) over the drum head, rounded rim side facing out (the bass drum hoop has a rounded side and a flat side, the flat side will be flush with the rim of the bass drum head and the rounded side will be flush with the bass drum claw