Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
The delay time can be set within the range of 200 ms to 1000 ms. PAN A panned delay in which the repeated sounds come alternately from the left and right channels. The delay time can be set within the range of 200 ms to 1000 ms. * When using the ME-50 in mono, the panning delay is not effective, even when PAN is selected. SPACE PAN This is a panning delay that gives an even wider spatial effect than PAN. The delay time can be set within the range of 200 ms to 1000 ms. * When using the ME-50 in mono, or when using headphones, the panning delay is not effective, even when SPACE PAN is selected. REVERSE This produces an effect where the sound is played back in reverse. You can get two different effects, “direct sound + effect sound,” or “effect sound only,” depending on the position of the E.LEVEL knob. When the E.LEVEL knob is turned up to MAX, the unit switches to “effect sound only.” The delay time can be set within the range of 400 ms to 2000 ms. Using the Effects Using the Effects Up to 2 seconds of performance content is recorded, then played back repeatedly. You can also layer this as you perform something else, then record these together (overdub). You can keep the recorded content playing continuously as backing and produce other special effects. “Using the HOLD Function” TAP This is a tempo delay that lets you set a dotted eighth note delay time for the performance tempo by pressing the DELAY pedal in time with the performance tempo. * The delay time can be set within the range of 46.5 ms to 1500 ms. 1. Set the TYPE knob to ‘TAP” The pedal indicator flashes in time with the current tempo. 2. Press the DELAY pedal in timing with the tempo more than two times. The reference tempo is determined by the time interval between each press of the pedal. The reference tempo is calculated in terms of quarter notes, and the delay time setting is the dotted eight note as referenced to the reference tempo. The pedal indicator flashes in time with the tempo. Timing Delay Sound TIME knob Adjuts the delay time. * When the type is set to “HOLD” or “TAP,” operating the TIME knob produces no effect. FEEDBACK knob Adjusts the amount of feedback (number of repeats). Turning the knob to the right increases the number of times the sound repeats. * When the type is set to ”HOLD,” operating the FEEDBACK knob produces no effect. E.LEVEL knob Adjusts the volume of the delay sound. When TYPE is set to REVERSE, this adjusts the balance of direct and effect sound. Adding a Delay Synchronized to the Performance Tempo Using tempo input, the delay time can be set within the range of 62 ms to 2000 ms. You can set this regardless of whether the effect is on or off. 1. Select the delay type. (except HOLD, TAP) 2. Hold down the DELAY pedal for at least two seconds. • If the DELAY pedal is pressed when the effect is on, the pedal indicator goes out, and the effect is turned off. • If the DELAY pedal is pressed when the effect is off, the pedal indicator turns red, and the effect is turned on. When you continue to depress the pedal, after two seconds the pedal’s indicator starts to flash, and the tempo can then be set with the effect on. Here, the delay time is indicated by the value set with the TIME knob. 3. Press the DELAY pedal in timing with the tempo more than two times. The delay time is set according to the time interval between each press of the pedal. The pedal indicator flashes in time with the tempo. * Press the pedal to set the tempo while no guitar sound is playing. * When the type is set to “PAN” or “SPACE PAN,” the delay time is set to half the interval between the presses of the pedal. 4. Hold down the pedal switch for at least two seconds to complete the tempo setting. The effect goes on, and instead of flashing, the pedal indicator will light. * The tempo may become confused momentarily when you go from Step 3 to Step 4. * If you move the TIME knob after finishing this setting, the delay time corresponding to the knob position takes effect. Using the Effects Using the Effects ) When the Tempo Has Been Set The delay time stored in a Patch (p. 20) is determined as follows. • If it is within the delay time range that can be set for the type currently selected, it is stored without change. • If it exceeds the maximum delay time that can be set for the type currently selected, the maximum value for the type is stored. • If it is less than the minimum delay time that can be set for the type currently selected, the minimum value for the type is stored. (Example) When TYPE is 100–500 ms When the delay time for the tempo setting is 600 ms: Stored as 500 ms. When the delay time for the tempo setting is 80 ms: Stored as 100 ms. Using the HOLD Function 1. Set the TYPE knob to HOLD. The unit goes into recording standby and the pedal’s indicator flashes at a fixed interval. * After switching to HOLD, wait two seconds before you carry out the next operation. 2. Press the DELAY pedal to start recording. Recording starts when you press t...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - ME-50 (1.77 mb)