Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
always replace the fuse with same exact otherwise instructed by an authorized American DJ ® service technician. Use of a different type fuse from that which is recommended cause fire or electric shock and will void the manufactures • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture. • Do not spill water or other liquids into or on to your unit. • Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to operate this unit if the power cord has been frayed or broken. • Disconnect from main power before making any type of connection. • Do not remove the cover under any conditions. There are no user serviceable parts inside. • Never plug this unit in to a dimmer pack. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall. • Do not attempt to operate this unit, if it becomes damaged. • This unit is intended for indoor use only, use of this product outdoors voids all warranties. • During long periods of non-use, disconnect the unit’s main power. • Always mount this unit in safe and stable matter. • Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 6 for cleaning details. • Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. © American DJ ® - - Emerald Beam™ Instruction Manual Page 4 Emerald Control & Functions SOUND MIN MIN LEVEL FUSE Model : Emerald Beam Serial No : ____________ Power : ___________ Fuse : ___________ Bulb : ___________ DANGER VISIBLE LASER RADIATION -AVOID DIRECT EYE EXPOSURE LASER DIODE WAVELENGTH : 532 nm Max Output : <4.9mW Class IIIa Laser Product AC 100-120V AC 200-240V Emerald Control & Functions SOUND MIN MIN LEVEL FUSE Model : Emerald Beam Serial No : ____________ Power : ___________ Fuse : ___________ Bulb : ___________ DANGER VISIBLE LASER RADIATION -AVOID DIRECT EYE EXPOSURE LASER DIODE WAVELENGTH : 532 nm Max Output : <4.9mW Class IIIa Laser Product AC 100-120V AC 200-240V 1 234 1. Audio Sensitivity Knob - This adjust audio sensitivity of the internal microphone (2). Turning the sensitivity knob in the clockwise direction will increase the sensitivity to sound. Turning the knob in the counter clockwise direction will decrease the fixture’s sensitivity to sound. 2. Microphone - This microphone receives external low frequencies to trigger the unit in Sound-Active mode. This microphone is designed to receive low frequency sounds only, tapping on the microphone and high pitch sounds may not trigger the unit. 3. Power Cord Connection - This connection is used to supply main power to the fixture. Use only the supplied I.E.C. power cord. Be sure the main power matches the required power of your fixture. 4. Fuse Holder - This housing stores the 2 amp GMA protective fuse. Always replace with the exact same type fuse, unless other wise instructed, by an authorized American DJ ® service technician. © American DJ ® - - Emerald Beam™ Instruction Manual Page 5 Emerald BeamOperation Power Supply: This unit is available before plugging your fixture in be sure the source voltage in your area matches the required voltage for your American DJ ® Emerald Beam.™ General Operation: Plug and Play operation. This fixture is designed to operate as a stand alone unit to sound. The Emerald Beam™ is ready to be plugged in, out of the After plugging the fixture in the laser will the many built in programs. The programs cycle through automatically when the unit is operating and may not be selected manually. The unit requires sound to operate and will automatically sound to conserve laser life. If the unit does not has been plugged in, be sure the sound sensitivity is tuned up (1), fuse has not blown, and the unit is properly plugged wall outlet. If problem continue to persist, please contact customer support for further instructions. Sensitivity Knob: A sound sensitivity knob is located on the rear of the unit. Use this knob to regulate the amount of sound it takes the unit. Turning the knob in a clockwise direction will increase the units sensitivity to sound, turning the knob in a counterclockwise direction will decrease the units sensitivity. Turning the knob completely to the counter-clockwise direction will turn off the sound-active mode. Emerald Beam™ Cleaning Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Clean the external optics with glass cleaner and a soft ...