Stimmen - 6, Durchschnittliche Bewertung: 4.2
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Set the clock master and sampling frequency correctly on the Rio-native device or in Dante Controller. Flash x2 Dante Network circuit is broken. Make sure that the Ethernet cables are not removed or short-circuited. Flash x3 Dante Network is wired incorrectly. (The devices are connected in a ring network, although the DAISY CHAIN setting has been selected, or they are connected in a daisy chain network, although the REDUNDANT setting has been selected, etc.) Make sure that the Ethernet cables are connected correctly. LightLight A non-GbE-compatible device is connected. Remove the non-GbE-compatible device from the Dante network. Flash Light The SECONDARY connector has taken over communications during redundant network operation. Check the circuit connected to the PRIMARY connector. Flash x2Light An abnormality has occurred on the circuit connected to the SECONDARY connector during redundant network operation. Check the circuit connected to the SECONDARY connector. Information Messages The indicators will remain lit and/or flashing cyclically to report the status. SYNC Indicators Description Possible Solution Synchronizing Please wait until the unit synchronizes completely. It Light may take up to 45 seconds to synchronize completely. Operating as the word clock master The unit is operating as the word clock master. Light or flash in different patterns Flash Owner’s Manual Specifications Specifications General Specifications Sampling Frequency Internal 44.1kHz 48kHz 88.2kHz 96kHz External 44.1kHz +4.1667%, +0.1%, –0.1%, –4.0% 48kHz +4.1667%, +0.1%, –0.1%, –4.0% 88.2kHz +4.1667%, +0.1%, –0.1%, –4.0% 96kHz +4.1667%, +0.1%, –0.1%, –4.0% ±200ppm ±200ppm ±200ppm ±200ppm Signal Delay Less than 3ms INPUT to OUTPUT, connect with CL5 using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz Frequency Response +0.5, –1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OUTPUT, Fs= 44.1kHz, 48kHz +0.5, –1.5dB 20Hz-40kHz, refer to +4dBu output @1kHz, INPUT to OUTPUT, Fs= 88.2kHz, 96kHz Total Harmonic Distortion*1 Less than 0.05% 20Hz-20kHz@+4dBu into 600., Fs= 44.1kHz, 48kHz Less than 0.05% 20Hz-40kHz@+4dBu into 600., Fs= 88.2kHz, 96kHz INPUT to OUTPUT, Input Gain= Min. Hum&Noise*2 –128dBu typ., Equivalent Input Noise, Input Gain= Max. –88dBu Residual output noise, ST master off. Dynamic Range 112dB typ., DA Converter, 108dB typ., INPUT to OUTPUT, Input Gain= Min. Crosstalk@1kHz –100dB*3, adjacent INPUT/OUTPUT channels, Input Gain= Min. Dimensions (WxHxD) and Net Weight Rio3224-D: 480mm x 232mm*4 x 361.5mm, 12.4kg Rio1608-D: 480mm x 144mm*4 x 361.5mm, 8.8kg Power Requirements (wattage) Rio3224-D: 120W Rio1608-D: 70W Power Requirements (voltage and hertz) US/Canada: 120V 60Hz Japan: 100V 50/60Hz China: 110-240V 50/60Hz Korea: 220V 60Hz Other: 110-240V 50/60Hz Temperature Range Operating temperature range: 0 - 40°C Storage temperature range: –20 -60°C Included Accessories Owner’s Manual, Power Cord *1. Total Harmonic Distortion is measured with 18dB/octave filter @80kHz *2. Hum & Noise are measured with A-Weight filter. *3. Crosstalk is measured with a 30dB/octave filter @22kHz *4. Including rubber feet. Owner’s Manual 18 Specifications Specifications Input Terminals GAIN Actual Load Impedance For Use With Nominal Input Level Connector Nominal Max. before clip INPUT 1-16 +66dB 10k. 50-600. Mics & 600. Lines –62dBu (0.616mV) –42dBu (6.16mV) XLR-3-31 type (Balanced)*1 +18dB –14dBu (155mV) +6dBu (1.55V) +17dB 3k. –13dBu (174mV) +7dBu (1.74V) –6dB +10dBu (2.45V) +30dBu (24.5V) INPUT 17-32*2 +66dB 10k. 50-600. Mics & 600. Lines –62dBu (0.616mV) –42dBu (6.16mV) XLR-3-31 type (Balanced)*1 +18dB –14dBu (155mV) +6dBu (1.55V) +17dB 3k. –13dBu (174mV) +7dBu (1.74V) –6dB +10dBu (2.45V) +30dBu (24.5V) *1. XLR-3-31 type connectors are balanced.(1=GND, 2=HOT, 3=COLD) *2. Rio3224-D only * In these specifications, 0dBu = 0.775 Vrms. * All input AD converters are 24bit linear, 128times oversampling. * +48V DC ( phantom power ) is supplied to INPUT XLR type connectors via each individual software controlled switch. Analog Output Characteristics Output Actual Source For Use With Max.Output Level Output Level Connector Terminals Impedance Nominal Select SW*1 Nominal Max. before clip OUTPUT 1-8 75. 600. Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type (Balanced)*2+18dB –2dBu (616mV) +18dBu (6.16V) OUTPUT 9-16*3 75. 600. Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type (Balanced)*2+18dB –2dBu (616mV) +18dBu (6.16V) *1. There are switches inside the body to preset the maximum output level. *2. XLR-3-32 type connectors are balanced. ( 1=GND, 2=HOT, 3=COLD ) *3. Rio3224-D only * All output DA converters are 24bit, 128times oversampling. * There are switches inside the body to preset the maximum output level. Digital I/O Characteristics Terminals Format Data length Level Audio Connector Primary/Secondary Dante 24bit or 32bit 1000Base-T 32ch (Rio3224-D to other devices) 24ch (Other devices to Rio3224-D...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - CL1 (3.55 mb)
Musikinstrumente - CL3 (3.55 mb)
Musikinstrumente - CL5 (3.55 mb)
Musikinstrumente - Rio1608-D (3.55 mb)