Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
OutputfunctionsInputfunctionsAppendices Globalfunctions PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 171 GEQ function GEQ function The range and direction of adjustment controlled by the faders can be selected from the following: ±15 dB, ±12 dB, ±6 dB (these are valid in both the boost and cut directions), or –24 dB (valid only in the cut direction). O EQ FLAT Resets all faders to the 0 dB position. When you click this button, a confirmation message will appear. P AUTO ASSIGN This button automates assignments to the DCA faders. If this button is on, the most recently selected region of GEQ bands will be assigned to the DCA faders when you access the GEQ PARAM screen. . When parametric EQ is selected UT V W Q R S Y Z a b X Q ASSIGN TO SELECTED CH ON/OFF button This switches the assignment to the SELECTED CHANNEL section on/off. Note If the AUTO ASSIGN button is off, switching the screen will make the ASSIGN TO SELECTED CH ON/OFF button turn off, and you’ll be able to use the SELECTED CHANNEL section to operate the parameters of the currently selected channel. U EQ FLAT This resets the GAIN parameter of all bands to the initial value (±0.0 dB). When you click this button, a confirmation message will appear. V LOWER/UPPER These indicators show which four bands (LOWER or UPPER) are selected in the SELECTED CHANNEL section of the panel. The text is shown in yellow to indicate the set of bands that is selected. W Knobs For each band, these knobs adjust the Q, the FREQ (center frequency), and GAIN (amount of boost/cut). X BYPASS This button bypasses each band of the EQ. Y (LOW shelving) If this button is on, the LOW EQ will be switched to a shelving-type. The Q knob will disappear. Z HPF (High Pass Filter) If this button is on, the LOW EQ will operate as a high pass filter. The Q knob will disappear, and the GAIN knob will be used to turn the HPF on/off. a LPF (Low Pass Filter) If this button is on, the HIGH EQ will operate as a low pass filter. The Q knob will disappear, and the GAIN knob will be used to turn the LPF on/off. b (HIGH shelving) If this button is on, the HIGH EQ will be switched to a shelving-type. The Q knob will disappear. R AUTO ASSIGN This button automates assignment to the SELECTED CHANNEL section. If you leave this button turned on, the selected frequency band will be assigned to the SELECTED CHANNEL section when you access the GEQ PARAM screen if the ASSIGN TO SELECTED CH ON/OFF button is on. S EQ TYPE This selects the EQ type. Turn the TYPE I button on to choose the algorithm used in conventional Yamaha digital mixers, or turn the TYPE II button on to choose a newly-developed algorithm. Using TYPE II will decrease the interference between bands. T EQ graph This graph shows the approximate response of the EQ parameters. The colored vertical line shows the FREQ (center frequency) of the band at which the cursor is located. (The color of each line is the same as the markings around the knob of each band.) When you edit the Q or GAIN (gain) of each band, the response curve will change accordingly. PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section GEQ ASSIGN screen GEQ ASSIGN screen ule settings, and shows the input/output levels. The signal path assignments and on/off status can also be edited in this screen. GEQ ASSIGN 5 1 2 3 4 A Level meter This meter indicates the peak level before and after the GEQ module. B Fader graph This indicates the approximate fader position for each band. When you click this area, the GEQ PARAM screen for the corresponding GEQ module will appear. You can also drag and drop this area onto another GEQ module to copy the GEQ settings. C GEQ ON/OFF button Switches the GEQ module on/off. D Insert destination Indicates the location at which the GEQ module is inserted. You can also specify the insert location from within this screen. E LINK button This button indicates the link status of adjacent odd- numbered > even-numbered GEQ modules. When you turn this button on, a window will appear, allowing you to select whether the parameters will be copied from one module to the other, or whether both modules will be initialized. 6 F DSP CONFIGURATION This box lets you change the number of assignments for the internal effects and GEQ modules. If you decrease the number of internal effects, the number of available GEQ modules will increase by one. The number of internal effects can be changed between eight units (twelve GEQ modules) to zero available internal effects (twenty GEQ modules). Note If you change the DSP CONFIGURATION setting, the internal effects or GEQ modules may be muted briefly. Input Output Globalfunctions Function Information Appendices functionsfunctions menu in the PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 173 GEQ function GEQ function Here you can recall, store, rename, or delete items in the GEQ library. GEQ LIBRARY 1 2 43 5 A EDIT When you click this button, the GEQ PARAM screen for the currently selected GEQ module will app...