Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The well-thought-out low-noise construction and natural phase sound will wield an unprecedented power in studio and on stage. NAME AND FUNCTIONS AC ADAPTOR JACK* RATE OUTPUT JACK PEDAL* Phaser PM-1 ♦ CHECK LAMP DEPTH »INPUT JACK SCREW RATE This knob controls speed of phase effect. At fully clockwise (0) position, a phase effect of high speed, 100ms, is attained and at fully counterclockwise (O) position, very low speed, 16s, phase is ef fee ted. DEPTH This knob controlsdepth of phase effect. Turn clockwise (O) for deeper effect and counterclockwise (O) for shallower effect. INPUT JACK This input jack receives output from electric guitar and other electronic in struments. OUTPUT JACK This jack feeds signal to amplifier. AC ADAPTOR JACK PH-1 operates both from self-contained battery {9V} and from AC line. Connect a BOSS AC Adaptor {DC9V) to this jack, and the battery is disconnected from the circuit, guranteeing stable long time performance. PEDAL SWITCH This is a changeover switch for Normal or Effect. By use of FET ELECTRONIC SWITCH, first in these kinds of small size effect units, pop noise is perfectly eliminated and PH-1 can be satisfactorily employed even in studio recording. CHECK LAMP While pedal is trod down, this lamp tights if battery is normal. Thus this lamp lets you confirm the changeover between Effect and Normal modes, and also battery state. If the indicator fails to light, replace the battery with a new one, SCREW When replacing battery, loosen this screw to open the casing. Do not remove off the screw from the pedal. If you do, be care ful not to lose it. BEFORE USING PH-1 • When operating PH-1 from AC line, use BOSS AC Adaptor for PH-1. • Avoid using PH-1 in very dusty location or under high temperature or humidity conditions. CONNECTING PH-1 AMPLIFIER Í ■ TO U AC ADAPTOR JACK BOSS AC ADAPTOR 'Ъ 00 RATI ♦* CHI PUT 1N*JT + Phaser PH-t - LEAD GUITAR BASS GUITAR BOSS PH-1 OPERATING PH-1 After connecting all cords required, set all knobs on the panel as illustrated. 2 Tread the pedal to check battery. If check lamp lights, battery is live. * If lamp does not light, which means dead battery, replace with a new battery. Tread pedal to set the unit in the state that sound is effected. Turn RATE control to proper position. Turn DEPTH control to proper position to obtain the depth you like. CHECK 0 0 RATE ■ « DEPTH CAUTIONS FOR REPLACING AND HANDLING BATTERY PEDAL (COVER) —SCREW BATTERY STRAP SPRING BASE COIL SPRING PEDAL GUIDE BATTERY CONNECTOR 9V BATTERY BATTERY HOUSING REPLACING BATTERY USE ONE 9'VOLT BATTERY. O Loosen the screw of pedal to open it and take out battery from its housing. ©Replace the battery by a fresh one and put it into position. 0 Set coil spring onto the projection on the rear of the pedal and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap in the cover or coil spring. CAUTIONS • When you don't use for a long period, remove the battery to prevent current leakage and leaking out of sticky substance. • If battery voltage drops, effect becomes inferior or no sound is produced. To prevent that, replace the battery a little earlier. * Be sure to keep the battery snapped by connector into the housing, when using AC adaptor, too. * Even if AC Adaptor cord comes out during performance, operations immediately changes to battery, causing no trouble in continued performance. • Power is switched on while a plug is put into input jack. When you do not use, keep the plug off the jack. AC ADAPTOR {OPTION) When you operate PH-1 from AC line, use AC adaptor for PH-1. BOSS ACA 120 FOR 117V AC BOSS ACA-240 FOR 240V AC ACA-220 FOR 220V AC SPECIFICATIONS Power...............Battery 9V (1) AC Adaptor Current draw...........DC9V, 7mA Control ..............Rate, Depth Others...............Normal/Effect Changeover Switch, Battery Check Lamp {also for confirmation of Normal/Effect changeover) Jack................Input, Output, AC Adaptor Phase shift.............4 steps, 720° LFO Speed............16 sec — 100msec S/N ratio .............Over 80dB Input impedance......... 220K12 Output load impedance.....Over 600ii Maximum input .........—20dB Gain................UNITY 1 Dimensions . . ........ . . 70{W)x55{H)x 125{D)mm Weight............... 400g * Specifications are subject to change without notice. n*=T\ ........... U| BLJSB Products of Roland Printed in Japan, Oct. '77 E-2 Roland®...